Hyundai Santa Fe (DM): Rear Wiper Motor. Repair procedures - Rear Wiper/Washer - Body Electrical SystemHyundai Santa Fe (DM): Rear Wiper Motor. Repair procedures

Inspection

Rear Wiper Motor
1.
Remove the connector from the rear wiper motor.
2.
Connect battery positive (+) and negative (-) cables to terminals 2 and 1 respectively.
3.
Check that the motor operates normally. Replace the motor if it operates abnormally.
No.
Description
1
Ground
2
Rear wiper motor (+)
3
Parking

Automatic Stop Operation Check
1.
Operate the motor at low speed using the stalk control.
2.
Stop the motor operation anywhere except at the off position by disconnecting terminal 3.
3.
Connect the positive (+) lead from the battery to terminal 3 and the negative (-) lead to terminal 1.
4.
Check that the motor stops running at the off position.


Removal

1.
Detach the rear wiper cap (A).

2.
Remove the rear wiper arm & blade (A) after removing rear wiper HEX nut (B).

3.
Remove the rear wiper cap & pad (A).

4.
Remove the cover (B) after loosening a rear wiper nut (A).

5.
Remove the tailgate trim after opening the tailgate.
6.
Disconnect the rear wiper motor connector (A) then remove the rear wiper motor (B) after loosening bolts (2EA).


Installation

1.
Install the rear wiper motor assembly.

Tightening torque Nut :
6.9~9.8 Nm (0.7~1.0 kgf.m, 5.0~7.2 lbf.ft)

2.
Install the tailgate trim.
3.
Install the rear wiper arm and rear wiper cap.

Tightening torque Nut (B) :
6.9~10.8 Nm (0.7~1.1 kgf.m, 5.0~8.0 lbf.ft)

4.
Install the rear wiper arm cap after tighting the nut.

Tightening torque Bolt :
13.7~16.7 N.m (1.4~1.7 kgf.m, 10.1~12.3 lbf.ft)

5.
Set the rear wiper blade and to the lowest defogger heat line and tailgate glass.


Components and Components Location
Component Location 1. Rear wiper arm & blade 2. Tailgate glass hole 3. Grommet 4. Rear wiper arm nut 5. Rear wiper motor assembly 6. Head cap 7. Rear wiper motor bolt ...

Rear Washer Switch. Repair procedures
Inspection 1. Check for continuity between the terminals while operating the wiper and washer switch. If it is not normal condition, replace wiper and wiper switch. Rear Wiper Switch Rear Washer Switch ...

See also:

Front Disc Brake. Components and Components Location
Components 1. Guide rod bolt 2. Bleed screw 3. Caliper carrier 4. Caliper body 5. Inner pad shim 6. Brake pad 7. Pad retainer ...

Intake Air Temperature Sensor (IATS). Specifications
Specification Temperature Resistance (kΩ) °C °F -40 -40 40.93 ~ 48.35 -20 -4 13.89 ~ 16.03 0 32 5.38 ~ 6.09 10 50 3.48 ~ 3.90 20 68 2.31 ~ 2.57 40 104 1.08 ~ 1.21 60 140 0.54 ~ 0.62 80 176 0.29 ...

Heated Oxygen Sensor (HO2S). Repair procedures
Inspection 1. Turn the ignition switch OFF. 2. Disconnect the HO2S connector. 3. Measure resistance between the HO2S terminals 4 and 5 [B1/S1]. 4. Measure resistance between the HO2S terminals 3 and 4 ...