Hyundai Santa Fe: Specifications - General Information - Engine Control/Fuel System - Hyundai Santa Fe DM 2013-2018 Service ManualHyundai Santa Fe: Specifications

Specifications

Fuel Delivery System
Items
Specification
Fuel Tank
Capacity
66 lit. (17.4 U.S.gal., 69.7 U.S.qt., 58.0 Imp.qt.)
Fuel Filter
Type
Paper type
Fuel Pressure
Low Pressure Fuel Line
480 ~ 520 kPa (4.9 ~ 5.3 kgf/cm², 69.6 ~ 75.4 psi)
High Pressure Fuel Line
3.0 ~ 15.0 MPa (30.6 ~ 153.0 kgf/cm², 435.1 ~ 2175.6 psi)
Fuel Pump
Type
Electrical, in-tank type
Driven by
Electric motor
High Pressure Fuel Pump
Type
Mechanical type
Driven by
Camshaft

Sensors
Manifold Absolute Pressure Sensor (MAPS)
▷ Type: Piezo-resistive pressure sensor type
▷ Specification
Pressure
[kPa (kgf/cm², psi)]
Output Voltage (V)
20.0 (0.20, 2.9)
0.79
46.7 (0.47, 6.77)
1.84
101.3 (1.03, 14.7)
4.0

Intake Air Temperature Sensor (IATS)
▷ Type: Thermistor type
▷ Specification
Temperature
Resistance (kΩ)
C
F
-40
-40
40.93 ~ 48.35
-20
-4
13.89 ~ 16.03
0
32
5.38 ~ 6.09
10
50
3.48 ~ 3.90
20
68
2.31 ~ 2.57
40
104
1.08 ~ 1.21
60
140
0.54 ~ 0.62
80
176
0.29 ~ 0.34

Engine Coolant Temperature Sensor (ECTS)
▷ Type: Thermistor type
▷ Specification
Temperature
Resistance (kΩ)
C
F
-40
-40
48.14
-20
-4
14.13 ~ 16.83
0
32
5.79
20
68
2.31 ~ 2.59
40
104
1.15
60
140
0.59
80
176
0.32

Throttle Position Sensor (TPS) [integrated into ETC Module]
▷ Type: Variable resistor type
▷ Specification
Throttle Angle()
Output Voltage (V)
TPS1
TPS2
0
0
5.0
10
0.48
4.52
20
0.95
4.05
30
1.43
3.57
40
1.90
3.10
50
2.38
2.62
60
2.86
2.14
70
3.33
1.67
80
3.81
1.19
90
4.29
0.71
100
4.76
0.24
105
5.0
0
C.T (6~15)
0.29 ~ 0.71
4.29 ~ 4.71
W.O.T (93~102)
4.43 ~ 4.86
0.14 ~ 0.57

Item
Resistance (kΩ)
TPS1
0.875 ~ 1.625 [20C(68F)]
TPS2
0.875 ~ 1.625 [20C(68F)]

Crankshaft Position Sensor (CKPS)
▷ Type: Hall effect type
Camshaft Position Sensor (CMPS)
▷ Type: Hall effect type
Knock Sensor (KS)
▷ Type: Piezo-electricity type
▷ Specification
Item
Specification
Capacitance (pF)
850 ~ 1,150

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 1]
▷ Type: Zirconia (ZrO2) [Linear] Type
▷ Specification
Item
Specification
Heater Resistance (Ω)
2.5 ~ 4.0 [20C(69.8F)]

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2]
▷ Type: Zirconia (ZrO2) [Binary] Type
▷ Specification
A/F Ratio (λ)
Output Voltage(V)
RICH
Approx. 0.9
LEAN
Approx. 0.04

Item
Specification
Heater Resistance (Ω)
3.3 ~ 4.1 [21C(69.8F)]

Rail Pressure Sensor (RPS)
▷ Type: Piezo-electricity type
▷ Specification

Accelerator Position Sensor (APS)
▷ Type: Variable resistor type
▷ Specification
Accelerator
Position
Output Voltage (V)
APS1
APS2
C.T
0.7 ~ 0.8
0.275 ~ 0.475
W.O.T
3.8 ~ 4.4
1.75 ~ 2.35

Fuel Tank Pressure Sensor (FTPS)
▷ Type: Piezo - Resistivity type
▷ Specification
Pressure
[kPa (kgf/cm², in H2O)
Output Voltage (V)
-3.75 (-0.038, -15.05)
4.5
0
1.5
+1.25 (0.013, 5.02)
0.5

Actuators
Injector
▷ Specification
Item
Specification
Coil Resistance (Ω)
1.18 ~ 1.31 [20C(68F)]

ETC Motor [integrated into ETC Module]
▷ Specification
Item
Specification
Coil Resistance (Ω)
1.2 ~ 1.8 [20C(68F)]

Purge Control Solenoid Valve (PCSV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
19.0 ~ 22.0 [20C(68F)]

CVVT Oil Control Valve (OCV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
6.9 ~ 7.9 [20C(68F)]

Variable Intake Solenoid (VIS) Valve
▷ Specification
Item
Specification
Coil Resistance (Ω)
30.0 ~ 35.0 [20C(68F)]

Fuel Pressure Control Valve
▷ Specification
Item
Specification
Coil Resistance (Ω)
0.5 [20C(68F)]

Ignition Coil
▷ Type: Stick type
▷ Specification
Item
Specification
Primary Coil Resistance (Ω)
0.62 10%[20C(68F)]
Secendary Coil Resistance (kΩ)
7.0 15%[20C(68F)]

Canister Close Valve (CCV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
19.9 ~ 22.9 [20C(68F)]


Service Standard

Item
Specification
Ignition Timing ()
BTDC 6 10
Idle Speed (rpm)
A/C OFF
Neutral, N, P-range
680 100
D-range
680 100
A/C ON
Neutral, N, P-range
680 100
D-range
680 100


Tightening Torques

Engine Control System
Item
kgf.m
N.m
lb-ft
ECM installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
ECM bracket installation bolt/nut
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Manifold absolute pressure sensor installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Crankshaft position sensor installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Crankshaft position sensor cover installation bolt (M6)
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Crankshaft position sensor cover installation bolt (M8)
1.9 ~ 2.4
18.6 ~ 23.5
13.7 ~ 17.4
Camshaft position sensor (Bank 1 / Intake) installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Camshaft position sensor (Bank 1 / Exhaust) installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Knock sensor installation bolt
1.9 ~ 2.4
18.6 ~ 23.5
13.7 ~ 17.4
Heated oxygen sensor (Bank 1 / sensor 1) installation
4.0 ~ 5.0
39.2 ~ 49.1
28.9 ~ 36.2
Heated oxygen sensor (Bank 1 / sensor 2) installation
4.0 ~ 5.0
39.2 ~ 49.1
28.9 ~ 36.2
Rail pressure sensor installation
1.8 ~ 2.2
18.0 ~ 22.0
13.3 ~ 16.2
Electronic throttle body installation bolt
0.8 ~ 1.0
7.8 ~ 9.8
5.8 ~ 7.2
Purge control solenoid valve bracket installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
CVVT oil control valve (Bank 1 / Intake) installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
CVVT oil control valve (Bank 1 / Exhaust) installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7
Ignition coil installation bolt
1.0 ~ 1.2
9.8 ~ 11.8
7.2 ~ 8.7

Fuel Delivery System
Item
kgf.m
N.m
lb-ft
Fuel tank installation bolt
4.5 ~ 6.0
44.1 ~ 58.8
32.5 ~ 43.4
Filler-neck assembly bracket installation bolt
0.4 ~ 0.6
3.9 ~ 5.9
2.9 ~ 4.3
Accelerator pedal module installation nut
1.7 ~ 2.6
9.8 ~ 14.7
7.2 ~ 10.8
Accelerator pedal module installation bolt
0.9 ~ 1.4
8.8 ~ 13.7
6.5 ~ 10.1
Delivery pipe installation bolt
1.9 ~ 2.4
18.6 ~ 23.5
13.7 ~ 17.4
High pressure fuel pump installation bolt
1.3 ~ 1.5
12.8 ~ 14.7
9.4 ~ 10.9
High pressure fuel pipe installation nut
2.7 ~ 3.3
26.5 ~ 32.4
19.5 ~ 23.9
High pressure fuel pipe function block installation bolt
0.8 ~ 1.2
7.8 ~ 11.8
5.8 ~ 8.7


    Special Service Tools
    Special Service Tools Item Illustration Application Fuel Pressure Gauge (09353-24100) Measuring the fuel line press ...

    See also:

    Passenger Airbag (PAB) Module. Repair procedures
    Removal 1. Disconnect the battery negative cable and wait for at least three minutes before beginning work. 2. Remove the glove box housin ...

    Delivery Pipe. Repair procedures
    Removal In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be in ...

    Power brakes
    Your vehicle has power-assisted brakes that adjust automatically through normal usage. In the event that the power-assisted brakes lose power because of a stalled engine or some other reason, you ...