Symptoms
|
Possible Causes
|
Remedy
|
Coolant leakage
|
| •
|
From the thermostat gasket
|
|
Check the mounting bolts
|
| •
|
Check the torque of the mounting bolts
|
|
| •
|
Retighten the bolts and check leakage again.
|
|
Check the gasket for damage
|
| •
|
Check gasket or seal for damage
|
|
| •
|
Replace gaskets and reuse the thermostat.
|
|
Cooled excessively
|
| •
|
Low heater performance (cool air blows-out)
|
| •
|
Thermogauge indicates 'LOW'
|
|
Visually check after removing the radiator cap.
|
| •
|
Insufficient coolant or leakage.
|
|
| •
|
After refilling coolant, recheck.
|
|
GDS check&Starting engine
|
| •
|
Check connection of the fan clutch or the
fan motor.
|
※ If the fan clutch is always connected, there will be
a noise at idle.
|
| •
|
Check the engine coolant sensor, wiring and
connectors.
|
| •
|
Replace the componants.
|
|
Remove the thermostat and inspect
|
| •
|
Check if there are dusts or chips in the
thermostat valve.
|
| •
|
Check adherence of the thermostat.
|
|
| •
|
Clean the thermostat valve and reuse the
thermostat.
|
| •
|
Replace the thermostat, if it doesn't work
properly.
|
|
Heated excessively
|
| •
|
Thermogauge indicates 'HI'
|
|
Visually check after removing the radiator cap.
|
| •
|
Insufficient coolant or leakage.
※ Be careful when removing a radiator cap
of the overheated vehicle.
|
| •
|
Check air in cooling system.
|
|
| •
|
After refilling coolant, recheck.
|
| •
|
Check the cylinder head gaskets for damage
and the tightening torque of the mounting bolts.
|
|
GDS check&Starting engine
|
| •
|
Check the fan motor performance as temperature
varies.
|
| •
|
Check if the fan clutch slips.
|
| •
|
Check the water pump adherence or impeller
damaged.
|
|
| •
|
Check the engine coolant sensor, wiring and
connectors.
|
| •
|
Check the fan motor, the relay and the connector.
|
| •
|
Replace the fan clutch, if it doesn't work
properly.
|
| •
|
Replace the water pump, if it doesn't work
properly.
|
|
Immerse the thermostat in boiling water and inspection.
|
| •
|
After removing the thermostat, check it works
properly.
|
※ Check the thermostat opens at the valve opening temperature.
|
| •
|
Replace the thermostat, if it doesn't work
properly.
|
|
Removal and Installation Removal of the thermostat would have an adverse effect, causing a lowering of cooling efficiency. Do not remove the thermostat, even if the engine tends to overheat. 1. Drain engine ...
Components 1. Water pump pulley 2. Water pump 3. Water pump gasket 4. Water pump housing 5. Water pump housing gasket 6. O-ring 7. Water inlet pipe ...
See also:
Tire replacement
If the tire is worn evenly, a tread wear indicator will appear as a solid band across the tread. This shows there is less than 1/16 in. (1.6 mm) of tread left on the tire. Replace the tire when this happens. ...
Tire rotation
To equalize tread wear, it is recommended that the tires be rotated every 7,500 miles (12,000 km) or sooner if irregular wear develops. During rotation, check the tires for correct balance. When rotating ...
Oil hydraulic Motor(Actuator). Repair procedures
Inspection If you have trouble code related to the oil hydraulic motor (actuator), check oil hydraulic motor (actuator) according to the inspection process. Oil Hydraulic Motor (Actuator) Inspection Procedure ...
Hyundai Santa Fe: Thermostat. Troubleshooting
Thermostat. Repair procedures
Water pump. Components and Components Location