Hyundai Santa Fe (TM): Rear Seat Belt - Body (Interior and Exterior)Hyundai Santa Fe (TM): Rear Seat Belt

Rear Seat Belt Retractor. Components and components location

Component Location

1. Second Row Seat Belt Retractor
2. Third Row Seat Belt Retractor

Rear Seat Belt Retractor. Repair procedures

Replacement
[Second row seat belt retractor]
  
•
When installing the belt, make sure not to damage the retractor.
1.
Remove the luggage side trim.
(Refer to Interior Trim - "Luggage Side Trim")
2.
Loosen the mounting bolt and remove the second row seat belt upper anchor (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

3.
Loosen the mounting bolt and remove the second row seat belt retractor(A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

4.
To install, reverse removal procedure.
  
•
Make sure the connector is plugged in properly.
•
Replace any damaged clips (or pin-type retainers).
[Third row seat belt retractor]
  
•
When installing the belt, make sure not to damage the retractor.
1.
Remove the luggage side trim.
(Refer to Interior Trim - "Luggage Side Trim")
2.
Loosen the mounting bolt and remove the Third row seat belt upper anchor (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

3.
Loosen the mounting bolt and remove the third row seat belt webbing guide (A).

4.
Loosen the mounting bolt and remove the third row seat belt retractor (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

5.
To install, reverse removal procedure.
  
•
Make sure the connector is plugged in properly.
•
Replace any damaged clips (or pin-type retainers).

Rear Center Seat Belt Retractor. Components and components location

Component Location

1. Rear center seat belt retractor


Rear Center Seat Belt Retractor. Repair procedures

Replacement
  
•
When installing the belt, make sure not to damage the retractor.
1.
Remove the second row seat back cover[LH].
(Refer to Rear Seat -"Rear Seat Back Cover")
2.
Loosen the rear center seat belt lower anchor mounting bolt (A) at the bottom of the second row seat cushion [LH].
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

3.
Loosen the mounting nut and remove the rear center seat belt retractor (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

4.
To install, reverse removal procedure.
  
•
Replace any damaged clips.

Rear Seat Belt Buckle. Components and components location

Component Location
[Second row seat belt buckle]

1. Second row seat belt buckle [LH]
2. Second row center seat belt buckle
3. Second row seat belt buckle [RH]

[Third row seat belt buckle]

1. Third row seat belt buckle


Rear Seat Belt Buckle. Repair procedures

Replacement
[Second row seat belt buckle]
  
•
Be sure to remove the second row center seat belt buckle (A) and the second row seat assembly [RH] (B) after removing the second row seat assembly [LH / RH].
1)
Second row seat assembly [LH] is positioned at the rearside, and second row seat assembly [RH] is positioned at the frontside.
2)
Loosen the mounting bolt (C) and remove the second row center seat belt buckle and the second row seat assembly [LH].

[Center]
1.
Remove the second row seat assembly [RH].
(Refer to Rear Seat -"Rear Seat Assembly")
2.
Loosen the mounting nut and remove the second row seat belt buckle (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

3.
To install, reverse removal procedure.
[RH]
1.
Remove the second row seat assembly [RH].
(Refer to Rear Seat -"Rear Seat Assembly")
2.
Loosen the mounting screw and remove the rear seat inner cover (A).

3.
Loosen the mounting bolt and remove the second row seat belt buckle [RH] (A)
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

4.
To install, reverse removal procedure.
  
•
The buckle and tongue of different types are impossible to be latched, so check that the buckle & tongue have the same types.
•
Distinguish the rear side seat buckle from the center seat buckle before latching.
•
If foreign materials are stuck in the inside button of buckle, it may cause interference during the latching process, leading to a functional problem (for example- beverages (viscous drinks), toothpicks, sand, plastic, vinyl, metal pieces, etc.).
•
After latching the buckle and tongue, check the fastening force using a Push-Pull Gauge (fastening force : 3kgf or less)
[Third row seat belt buckle]
1.
Remove the third row seat assembly [RH].
2.
Loosen the mounting bolt and remove the third row seat belt buckle [LH] (A).
Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m , 28.9 - 39.8 lb-ft)

3.
To install, reverse removal procedure.
Front Seat Belt
Components and components location Components 1. Front seat belt retractor 2. Second row seat belt retractor 3. Third row seat belt retractor Front Seat Belt Pretensioner. Components and components location ...

See also:

Variable Intake Solenoid (VIS) Valve. Specifications
Specification Item Specification Coil resistance (Ω) 30.0 ~ 35.0 [20°C(68°F)] ...

ETC (Electronic Throttle Control) System. Repair procedures
Inspection Throttle Position Sensor (TPS) 1. Connect the GDS on the Data Link Connector (DLC). 2. Start the engine and measure the output voltage of TPS 1 and 2 at C.T. and W.O.T. Specification: Refer ...

California perchlorate notice
Perchlorate Material-special handling may apply, See www.dtsc.ca.gov/hazardouswaste/ perchlorate. Notice to California Vehicle Dismantlers: Perchlorate containing materials, such as air bag inflators, ...