Hyundai Santa Fe (DM): Brake Pedal. Repair procedures - Brake System - Brake SystemHyundai Santa Fe (DM): Brake Pedal. Repair procedures

Removal

1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the crash pad lower panel.
3.
Remove the shower duct (A).

4.
Disconnect the stop lamp switch connector (A).

5.
Remove the brake pedal member mounting nut (A).

6.
Remove the snap pin (A) and clevis pin (B).

7.
Remove the brake pedal member assembly mounting nuts (A) and then remove the brake pedal assembly.


Inspection

1.
Check the bushing for wear.
2.
Check the brake pedal for bending or twisting.
3.
Check the brake pedal return spring for damage.
4.
Check the stop lamp switch.
(1)
Connect a circuit tester to the connector of stop lamp switch, and check whether or not there is continuity when the plunger of the stop lamp switch is pushed in and when it is released.
(2)
The stop lamp switch is in good condition if there is no continuity when plunger(A) is pushed.


Installation

1.
Pre-tighten the bracket fixing bolt (A) in dash panel.

2.
Install the brake booster and brake pedal member fixing nuts (A) securely.

Tightening torque:
16.7 ~ 25.5 N.m (1.7 ~ 2.6 kgf.m, 12.3 ~ 18.8 lb-ft)

3.
Tighten the bolt (A) securely in dash panel.

Tightening torque:
16.7 ~ 25.5 N.m (1.7 ~ 2.6 kgf.m, 12.3 ~ 18.8 lb-ft)

4.
Install the snap pin (A) and clevis pin (B).

•
Before installing the pin, apply the grease to the clevis pin.
•
Use a new snap pin whenever installing.
5.
Install the stop lamp switch securely.
6.
Connect the stop lamp switch connector (A).

7.
Adjust the brake pedal height and free play.
8.
Check the brake pedal operation after installing the brake pedal.
9.
Install the shower duct (A).

10.
Install the crash pad lower panel.
11.
Reconnect the battery negative cable.

Adjustment

Stop lamp switch clearance adjustment
If the gap between stop lamp switch and bracket is not 1.0 ~ 2.0mm(0.04~ 0.08in), perform the procedure below.
1.
Disconnect the stop lamp switch connector (A).

2.
Pull the locking plate (A) as indicated by the arrow.

3.
Turn stop lamp switch 45° counterclockwise and remove it.

4.
While holding the brake pedal, insert the stop lamp switch until the plunger is fully pressed in against the stopper on the pedal assembly.

5.
After inserting, turn the stop switch (A) 45° clockwise, and then assemble locking plate (B) by pushing.

6.
Confirm the gap between stop lamp switch and bracket.

Stop lamp clearance:
1.0 ~ 2.0 mm (0.04 ~ 0.08 in)

7.
Connect the stop lamp switch connector.

Brake Pedal. Components and Components Location
Components 1. Cowl bracket 2. Brake pedal member assembly 3. Stop lamp switch 4. Return spring 5. Brake pedal stopper 6. Brake pedal arm 7. Brake pedal pad ...

Front Disc Brake. Components and Components Location
Components 1. Guide rod bolt 2. Bleed screw 3. Caliper carrier 4. Caliper body 5. Inner pad shim 6. Brake pad 7. Pad retainer ...

See also:

Luggage Side Trim. Components and Components Location
Component Location 1. Luggage side trim ...

California perchlorate notice
Perchlorate Material-special handling may apply, See www.dtsc.ca.gov/hazardouswaste/ perchlorate. Notice to California Vehicle Dismantlers: Perchlorate containing materials, such as air bag inflators, ...

Side Impact Sensor (SIS). Components and Components Location
Components ...