Replacement
[Center pillar lower trim]
•
|
Put on gloves to protect your hands.
|
|
•
|
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts, to prevent damage.
|
•
|
Use a plastic panel removal tool to remove interior trim
pieces to protect from marring the surface.
|
•
|
Take care not to bend or scratch the trim and panels.
|
|
1. |
Remove the front door scuff trim.
|
2. |
Remove the rear door scuff trim.
|
3. |
Slighty remove the front door body side weatherstrip.
|
4. |
Slighty remove the rear door body side weatherstrip.
|
5. |
Remove the seat belt lower anchor cover (A).
|
6. |
After loosening the mounting bolt, then remove the seat belt lower
anchor (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
7. |
Using a screwdriver or remover, remove the center pillar lower
trim (A).
|
8. |
Install in the reverse order of removal.
• |
Replace any damaged clips.
|
|
|
•
|
Put on gloves to protect your hands.
|
|
•
|
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts, to prevent damage.
|
•
|
Use a plastic panel removal tool to remove interior trim
pieces to protect from marring the surface.
|
•
|
Take care not to bend or scratch the trim and panels.
|
|
1. |
Remove the front door scuff trim.
|
2. |
Remove the rear door scuff trim.
|
3. |
Slighty remove the front door body side weatherstrip.
|
4. |
Slighty remove the rear door body side weatherstrip.
|
5. |
To remove the locking mechanism (A), using a (-) driver (B) turn
it counter clockwise. from the EFD(Emergency Fastening Device) system
(C).
|
6. |
Using a screwdriver or remover, remove the center pillar lower
trim (A).
|
7. |
Install in the reverse order of removal.
• |
Replace any damaged clips.
|
|
|
[Center pillar upper trim]
•
|
Put on gloves to protect your hands.
|
|
•
|
When prying with a flat-tip screwdriver, wrap it with
protective tape, and apply protective tape around the related
parts, to prevent damage.
|
•
|
Use a plastic panel removal tool to remove interior trim
pieces to protect from marring the surface.
|
•
|
Take care not to bend or scratch the trim and panels.
|
|
1. |
Remove the center pillar lower trim.
|
2. |
After loosening the mounting bolt, then remove the center pillar
upper trim (A).
|
3. |
Install in the reverse order of removal.
• |
Replace any damaged clips.
|
|
|
Component Location 1. Center pillar lower trim 2. Center pillar upper trim ...
Component Location 1. Rear transverse trim ...
See also:
Checking the engine oil level
Type A Type B 1. Be sure the vehicle is on level ground. 2. Start the engine and allow it to reach normal operating temperature. 3. Turn the engine off and wait for a few minutes (about 5 minutes) for ...
Knock Sensor (KS). Description and Operation
Description Knocking is a phenomenon characterized by undesirable vibration and noise and can cause engine damage. Knock Sensor (KS) is installed on the cylinder block and senses engine knocking. When ...
Front Door Latch. Repair procedures
Replacement 1. Remove the front door module. 2. Remove the front door outside handle base (A) by pushing in the lock pins located in the back. 3. Open the front door outside handle cable cap (A). 4. Remove ...