Hyundai Santa Fe (DM): Cruise Control Switch. Repair procedures - Cruise Control System - Engine Electrical SystemHyundai Santa Fe (DM): Cruise Control Switch. Repair procedures

Removal

1.
Disconnect the negative (-) battery terminal.
2.
Remove the driver airbag module.
<a href="content.asp?vehicletype=Passenger&mfrcode=HY&area=HMA&langcode=ENG&modelid=AN13&modelyr=2013&mmctype=ab&mmcid=36&group=SHOP&pdftype=&cat1=2013+%3E+G+2%2E0+T%2DGDI&ec=&nLocation=1$2_1_3_1&firstnodedesc=Restraint&sitinfolist=81%5E8120%5E81200100%5Enone%5E801%5E1%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%2481%5E8120%5E81200100%5Enone%5E801%5E4%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%2481%5E8120%5E81200100%5Enone%5E801%5E8%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")</a>
3.
Remove the steering wheel.
<a href="content.asp?vehicletype=Passenger&mfrcode=HY&area=HMA&langcode=ENG&modelid=AN13&modelyr=2013&mmctype=st&mmcid=4&group=SHOP&pdftype=&cat1=2013+%3E+G+2%2E0+T%2DGDI&ec=&nLocation=1$11_1_3_5&firstnodedesc=Steering+System&sitinfolist=61%5E6125%5E61250500%5Enone%5E801%5E1%5EENG%5EHY%5EAN13%5E2013%5Est%5E4%5Enone%5Enone%5Enone%5ESHOP%5E%2461%5E6125%5E61250500%5Enone%5E801%5E2%5EENG%5EHY%5EAN13%5E2013%5Est%5E4%5Enone%5Enone%5Enone%5ESHOP%5E%2461%5E6125%5E61250500%5Enone%5E801%5E4%5EENG%5EHY%5EAN13%5E2013%5Est%5E4%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Steering System - "Steering Column and Shaft")</a>
4.
Remove the steering wheel cover (A) after loosening the screws.
Плиты железобетонные класс грузоподъемности.

5.
Loosen the screws after disconnecting the steering wheel remote control switch connector (A).
6.
Remove the remote control switchs (A).

Installation

1.
Install in the reverse order of removal.

Inspection

[Measuring Resistance]
1.
Disconnect the cruise control switch connector from the control switch.
2.
Measure resistance between terminals on the control switch when each function switch is ON (switch is depressed).
Function switch
 Terminal
 Resistance [kΩ ± 5%]
CANCEL
 2 - 7
 0.18
RES+
 2 - 7
 0.33
SET–
 2 - 7
 0.55
CRUISE
 2 - 7
 0.88

3.
If not within specification, replace switch.
[Measuring Voltage]
1.
Connect the cruise control switch connector to the control switch.
2.
Measure voltage between terminals on the harness side connector when each function switch is ON (switch is depressed).
Function switch
 Terminal
 Voltage (V)
CANCEL
 2 - 7
 0.76
RES+
 2 - 7
 1.41
SET–
 2 - 7
 2.05
CRUISE
 2 - 7
 2.66

3.
If not within specification, replace switch.

Cruise Control Switch. Schematic Diagrams
Circuit Diagram ...

Emission Control System
...

See also:

Opening the fuel filler lid
The fuel filler lid must be opened from inside the vehicle by pulling the fuel filler lid opener lever located on the driver’s door. ✽ NOTICE If the fuel filler lid will not open because ice ...

Roof Trim Assembly. Repair procedures
Replacement • Put on gloves to protect your hands. • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage. • ...

Knock Sensor (KS). Description and Operation
Description Knocking is a phenomenon characterized by undesirable vibration and noise and can cause engine damage. Knock Sensor (KS) is installed on the cylinder block and senses engine knocking. When ...