Hyundai Santa Fe (DM): Delivery Pipe. Repair procedures - Fuel Delivery System - Engine Control/Fuel SystemHyundai Santa Fe (DM): Delivery Pipe. Repair procedures

Removal

In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be injury caused by leakage of the high pressure fuel. So don’t do any repair work right after engine stops.
1.
Turn the ignition switch OFF and disconnect the battery negative (-) cable.
2.
Release the residual pressure in fuel line.
(Refer to Fuel Delivery System - “Release Residual Pressure in Fuel Line”)
When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the GDS after completion of “Release Residual Pressure in Fuel Line” work.
3.
Remove the intake manifold.
(Refer to Engine Mechanical System - "Intake Manifold")
4.
Remove the injector form (A).
5.
Disconnect the injector connectors (A) and the rail pressure sensor connector (B).
6.
Remove the high pressure fuel pipe (C).
7.
Remove the installation bolt (D), and then remove the delivery pipe and injector assembly from the engine.

Installation

•
Install the component with the specified torques.
•
Apply engine oil to the injector O-ring.
•
Do not use already used injector O-ring again.
•
Do not reuse the bolts.
•
When insert the injector, be careful not to damage the injector tip.
•
Use proper tooling for change of combustion seal. Take proper precautions not to damage surface during assembly or disassembly.
•
Avoid dropping the fuel pipe (including injectors) or bumping it into any hard objects sincedamage to the internal components may occur. If necessary, visually inspect and confirmproper operation with performance tests prior to reuse.
•
Before installing the injector into the cylinder head, clean the injector hole and avoidcontaminants from entering inside the injector hole. When installing the injector, avoid bumpingthe injector tip into any of the surrounding components since the tip may become damagedfrom the impact.
•
When fastening the three fuel delivery pipemounting bolts, fully hand-tighten first, andthen tighten in the proper sequence () in several cycles up tothe specified → ) in several cycles up tothe specified → torque. The delivery pipeshould move less than 1/8 inch (approx.3mm),) in several cycles up tothe specified torque. The delivery pipeshould move less than 1/8 inch (approx.3mm), whenever each bolt is tightened.

1.
Install in the reverse order of removal.
Delivery pipe installation bolt:
18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)
High pressure fuel pipe installation nut:
26.5 ~ 32.4 N.m (2.7 ~ 3.3 kgf.m, 19.5 ~ 23.9 lb-ft)

Accelerator Pedal. Repair procedures
Removal 1. Turn the ignition switch OFF and disconnect the negative (-) battery cable. 2. Disconnect the accelerator position sensor connector (A). 3. Remove the installation nuts (C), the bolt (B) and ...

High Pressure Fuel Pump. Repair procedures
Removal In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be injury caused by leakage of the high pressure fuel. So don’t do any repair ...

See also:

Troubleshooting
Fault Diagnosis Features a fail-safe mechanism that provides "limp-home" 4th gear hold to enable the vehicle to be driven to the owner's home or dealer shop. Fail-Safe: The TCM provides 4th ...

This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause ...

Highway driving
Tires: Adjust the tire inflation pressures to specification. Low tire inflation pressures will result in overheating and possible failure of the tires. Avoid using worn or damaged tires which may result ...