Hyundai Santa Fe (DM): Parking Brake Lever Assembly. Repair procedures - Parking Brake System - Brake SystemHyundai Santa Fe (DM): Parking Brake Lever Assembly. Repair procedures

Removal

The parking brake cables must not be bent or distorted. This will lead to stiff operation and premature failure.
1.
Remove the floor console assembly.
2.
Disconnect the connector (A) of parking brake switch.

3.
Loosen the adjusting nut (A) and the parking brake cables (B).

Parking brake lever in the car must be in fully loosened position.
4.
Remove the parking brake lever assembly (A) after removing the bolts.


Installation

1.
Install the parking brake lever assembly (A).

Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)

2.
Install the parking brake cable (B) and tighten the adjusting nut (A).

3.
Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.

Specified grease:
Multi purpose grease SAE J310, NLGI No.2

4.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke:
5 ~ 6 clicks (Pull the lever with 196N (20 kgf, 44 lbf))

After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

5.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
6.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
7.
Reconnect the connector (A) of parking brake switch.

Inspect the continuity of parking brake switch.

When the brake lever is pulled: continuity
When the brake lever is released: no continuity

8.
Install the floor console.

Adjustment

Parking Brake Lever Stroke Adjustment
1.
Remove the floor console.
2.
Apply the brake pedal 20 times with the force of 10kgf after bleeding. Then, for the cable to settle in, apply the parking brake full stroke more than 3 times.
3.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).

Parking brake lever stroke :
5 ~ 6 clicks (Pull the lever with 196N (20 kgf, 44 lbf))

After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

4.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
5.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
6.
Install the floor console.

Parking Brake Assembly. Repair procedures
Removal Parking Brake Shoe 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the rear tire and wheel. 3. Remove the rear brake caliper and Rear disc brake. 4. Remove the parking brake ...

Parking Brake Pedal Assembly. Repair procedures
Removal 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the crash pad lower panel. 3. Remove the junction box. 4. Disconnect the parking brake switch connector. 5. ...

See also:

Driving off-road
Drive carefully off-road because your vehicle may be damaged by rocks or roots of trees. Become familiar with the off-road conditions where you are going to drive before you begin driving. ...

Good driving practices
Never move the shift lever from P (Park) or N (Neutral) to any other position with the accelerator pedal depressed. Never move the shift lever into "P" when the vehicle is in motion. Be sure ...

CVVT & Camshaft. Repair procedures
Removal 1. Remove the cylinder head cover. 2. Set No.1 cylinder to TDC/compression. A. Turn the crankshaft pulley and align its groove with the timing mark "T" of the lower timing chain cover. ...