Hyundai Santa Fe (DM): Passive Occupant Detection System (PODS-F). Repair procedures - SRSCM - RestraintHyundai Santa Fe (DM): Passive Occupant Detection System (PODS-F). Repair procedures

Hyundai Santa Fe DM 2013-2018 Service Manual / Restraint / SRSCM / Passive Occupant Detection System (PODS-F). Repair procedures

Removal

PODS-F ODU (Occupant Detection Unit)
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the front passenger seat assembly.
3.
Disconnect the PODS-F ODU connector.
4.
Remove the PODS-F ODU.
PODS-F Mat
1.
Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2.
Remove the front passenger seat assembly.
3.
Disconnect the PODS-F mat connector.
4.
Remove the front seat cushion assembly

Installation

PODS-F ODU
1.
Install the PODS-F ODU on the Front seat track assembly.
2.
Connect the PODS-F ODU connector.
3.
Install the front passenger seat assembly.
4.
Reconnect the battery negative cable.
5.
After installing the PODS-F, confirm proper system operation :
A.
Turn the ignition switch ON the SRS indicator should be turned on for about six seconds and then go off.
B.
Telltale lamp will turn on for 4 seconds and be turned off for 3 seconds. After the 7 seconds, it shall remain off if the PODS-F does not require suppression and the passenger airbag is enabled.
Be sure to perform PODS-F reset with GDS after replacing PODS-F ODU in the seat track.
PODS-F Mat
1.
Install the PODS-F Mat equipped seat cushion assembly on the front seat assembly.
2.
Connect the PODS-F mat connector.
3.
Install the front passenger seat assembly.
4.
Reconnect the battery negative cable.
5.
After installing the PODS-F, confirm proper system operation :
A.
Turn the ignition switch ON the SRS indicator should be turned on for about six seconds and then go off.
B.
Telltale lamp will turn on for 4 seconds and be turned off for 3 seconds. After the 7 seconds, it shall remain off if the PODS-F does not require suppression and the passenger airbag is enabled.
Be sure to perform PODS-F zeroing with GDS after replacing PODS-F equipped seat cushion.

PODS-F zeroing Procedure

You should perform PODS-F Re-zero procedure after service or replacement about all part of the passenger seat.
-
Seat assembly, Seat foam and Seat Cushion Assembly Replacement (PODS-F ODU No Replacement): C1[Auto]
-
PODS-F ODU Replacement: C2[Manual]:
C1[Auto] Procedure
1.
Ignition “OFF”, connect GDS.
2.
Ignition “ON” & Engine “OFF”, select Airbag system and “PODS-F Reset” mode.
3.
Select C1.
C1[Auto] : When replacing seat assembly or Seat foam.
4.
The GDS will show the two PODS-F Zeroing function steps.
(1)
Erase PODS-F diagnostic codes.
(2)
PODS-F initialization.

This step must be done PODS-F re-zero, when the front passenger seat is empty.
5.
The PODS-F initialization procedure will be performed.

[Heater type]

[No heater type]

[Vent heater type]

Erase the SRSCM diagnostic codes after completing the PODS-F zeroing.
C2[Manual] Procedure
1.
Ignition “OFF”, connect GDS.
2.
Ignition “ON” & Engine “OFF”, select Airbag system and “PODS-F Reset” mode.
3.
Select C2.
C2[Manual]: When replacing PODS-F ODU
4.
Select seat type.
5.
The GDS will show the two PODS-F Zeroing function steps.
(1)
Erase PODS-F diagnostic codes.
(2)
PODS-F initialization.

This step must be done PODS-F re-zero, when the front passenger seat is empty.
6.
The PODS-F initialization procedure will be performed.

[Heater type]

[No heater type]

[Vent heater type]

Erase the SRSCM diagnostic codes after completing the PODS-F zeroing
In case of zeroing failure
-
Fail Code 2 : PODS ECU Fault
-
Fail Code 3 : sensor short
-
Fail Code 4 : Sensor Open
-
Fail Code 8 : Wet seat
-
Fail Code 9 : Empty seat or seat type mismatch
-
Fail Code 10 : Electronic noise is too much
-
Fail Code A : Spilt water on the Seat
-
Fail Code B : Wet Seat foam
-
Fail Code D : Humidity is too High
-
Fail Code E : Temperature is too low

Passive Occupant Detection System (PODS-F). Components and Components Location
Components ...

Schematic Diagrams
Circuit Diagram (1) Circuit Diagram (2) Circuit Diagram (3) SRSCM Connector terminal Pin Function (Connector A) Pin Function (Connector B) 1 Ignition 1 Seat belt pretensioner [Driver] High 2 Passenger ...

See also:

TPMS Sensor. Description and Operation
Description 1. Function A. By detecting the pressure, temperature, acceleration, and battery condition, transmit information to ECU by a wireless RF. B. Wheel location is recognized by comparing with Wheel ...

Seat Belt Warning Light
This warning light informs the driver that the seat belt is not fastened. For more details, refer to the “Seat Belts” in chapter 3. ...

Dynamic Damper. Repair procedures
Removal 1. Remove the front driveshaft. 2. Remove the TJ joint assembly. 3. Remove the remove the both side of band (B) of the dynamic damper (A). 4. Fix the driveshaft (A) with a vice (B) as illustrated. ...