Removal
Pressure Side Impact Sensor (P-SIS)
•
|
Removal of the airbag must be performed according to the
precautions/procedures described previously.
|
•
|
Before disconnecting the side impact sensor connector(s),
disconnect the side airbag connector(s).
|
•
|
Do not turn the ignition switch ON and do not connect
the battery cable while replacing the side impact sensor.
|
|
1. |
Disconnect the battery negative cable, and wait for at least three
minutes before beginning work.
|
2. |
Remove the front door trim.
|
3. |
Disconnect the pressure side impact sensor (A) connector and remove
the pressure side impact sensor mounting screws.
|
Rear Side Impact Sensor
1. |
Disconnect the battery negative cable and wait for at least three
minutes before beginning work.
|
2. |
Remove the luggage side trim.
|
3. |
Disconnect the rear side impact sensor connector.
|
4. |
Loosen the rear side impact sensor mounting bolt and then remove
the rear side impact sensor (A).
|
Installation
Pressure Side Impact Sensor
1. |
Install the new pressure side impact sensor (A) with the screws
then connect the pressure side impact sensor connector.
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)
|
• |
Use the specified screws only.
|
|
|
2. |
Install the front door trim.
|
3. |
Reconnect the battery negative cable.
|
4. |
After installing the pressure side impact sensor, confirm proper
system operation:
A. |
Turn the ignition switch ON; the SRS indicator light should
be turned on for about six seconds and then go off.
|
• |
You must comply with the specified tightening
torques with the tool specified because Pressure – Side
Impact Sensors (P-SIS) may be broken or the POP-NUT
may be rotated.
|
• |
Problems may be occurred in the durability of
P-SIS or impact sensing performance may be depreciated
if POP-NUT is rotated.
|
• |
The door module must not be transformed because
SRSCM judges a impact through the pressure sensor in
the door module.
|
|
|
Rear Side Impact Sensor
•
|
Do not turn the ignition switch ON and do not connect
the battery cable while replacing the side impact sensor.
|
|
1. |
Install the new rear side impact sensor with a bolt and then connect
the rear side impact sensor connector.
Tightening torque:
6.8 ~ 9.2 N.m (0.7 ~ 0.94 kgf.m, 5.0 ~ 6.8 lb-ft)
|
|
2. |
Install the luggage side trim.
|
3. |
Reconnect the battery negative cable.
|
4. |
After installing the Side Impact Sensor, confirm proper system
operation:
A. |
Turn the ignition switch ON; the SRS indicator light should
be turned on for about six seconds and then go off.
|
|
Description The SRSCM shall monitor the status of the driver and front passenger seat belt buckle. The SRSCM provides one pin each for the driver and front passenger seat belt buckle status input. The ...
See also:
Seat cushion height (for driver’s seat)
To change the height of the seat cushion, push the lever upwards or downwards. To lower the seat cushion, push the lever down several times. To raise the seat cushion, pull the lever up several times. ...
Hazard Lamp Switch. Repair procedures
Inspection 1. The SJB can be diagnosed by using the GDS. The SJB communicates with the GDS which then displays inputs and outputs along with codes. It will be able to diagnose defects of hazard lamp switch ...
Emergency fuel filer door release
If the fuel filler door does not open using the remote fuel filler door release, you can open it manually. Unsnap and remove the panel in the cargo area. Pull the handle outward slightly. CAUTION Do not ...