Hyundai Santa Fe (DM): Smart Key Unit. Repair procedures
Removal
Smart Key Unit
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the driver crash pad lower panel.
|
3. |
Remove the smart key unit (B) after loosening the
mounting bolts(2EA) and disconnecting the connector (A).
Hvac repair services emergency response Cranford platinum hvac.
|
RF Receiver
Take care not to scratch the crash pad and related
parts.
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the crash pad center panel.
|
3. |
Remove the RF receiver after loosening the mounting
nut (1EA) and disconnecting the connector.
|
Interior 1 Antenna
Take care not to scratch the crash pad and related
parts.
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the crash pad center panel.
|
3. |
Remove the interior 1 antenna (B) after loosening
the mounting nuts (2EA) and disconnecting the connector (A).
|
Interior 2 Antenna
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the console rear complete assembly.
|
3. |
Remove the interior 2 antenna (B) after loosening
the mounting nuts (2EA) and disconnecting the connector (A).
|
Interior 3 Antenna
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the luggage covering mat (A).
|
3. |
Remove the luggage floor box (A) after loosening
the screws (4EA).
|
4. |
Remove the luggae tray box (A).
|
5. |
Remove the floor mat (A) after loosening the screws
(4EA).
|
6. |
Remove the interior 3 antenna (B) after loosening
the mounting screws(2EA) and disconnecting the connector (A).
|
Exterior Bumper Antenna
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the rear bumper cover.
|
3. |
Disconnect the antenna connector (A) on the center
of rear bumper.
|
4. |
After loosening the nuts (2EA), remove the exterior
bumper antenna (B).
|
Buzzer
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the front left wheel guide.
|
3. |
Disconnect the connectors, then remove the buzzer
(A).
|
Door Outside Handle
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the door outside handle cover (A) after seperating
the plug hole (B) from the door and loosening the mounting bolt.
|
3. |
Remove the outside handle (A) by sliding it rearward.
|
4. |
Disconnect the door outside handle connector (A).
|
Tailgate Open Switch
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the tailgate trim.
|
3. |
Remove the tailgate back panel.
|
4. |
Loosen the tailgate switch mounting screws (2EA).
|
5. |
Remove the tailgate switch (A) after seperating the
license lamp wiring.
|
Inspection
Smart Key Unit
Refer to Smart Key System - "Smart Key Diagnostic"
Smart Key Switch
Refer to Smart Key System - "Smart Key Diagnostic"
Antenna
Refer to Smart Key System - "Smart Key Diagnostic"
Tailgate Switch
1. |
Check for continuity between the tailgate latch terminals.
|
2. |
If continuity is not specified, inspect the switch
|
Installation
Smart Key Unit
1. |
Install the smart key unit.
|
2. |
Install the smart key unit mounting bolts and connect
the connector.
|
3. |
Install the driver side crash pad lower panel.
|
4. |
Install the negative (-) battery terminal and check
the smart key system.
|
RF Receiver
1. |
Install the RF receiver.
|
2. |
Install the RF receiver mounting nut and connect
the connector.
|
3. |
Install the crash pad center panel.
|
4. |
Install the negative (-) battery terminal and check
the smart key system.
|
Interior 1 Antenna
1. |
Install the interior 1 antenna.
|
2. |
Install the crash pad center panel.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
Interior 2 Antenna
1. |
Install the interior 2 antenna.
|
2. |
Install the console rear complete assembly.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
Interior 3 Antenna
1. |
Install the interior 3 antenna.
|
2. |
Install the floor mat, the luggage tray box, the
luggage floor box and luggage covering mat.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
Exterior Bumper Antenna
1. |
Install the exterior bumper antenna.
|
2. |
Install the rear bumper cover.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
Buzzer
1. |
Install the buzzer.
|
2. |
Install the front left wheel guide.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
Door Outside Handle
1. |
Install the outside handle.
|
2. |
Install the door trim.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
Tailgate Switch
1. |
Install the tailgate switch.
|
2. |
Install the tailgate garnish.
|
3. |
Install the tailgate trim.
|
4. |
Install the negative (-) battery terminal and check
the smart key system.
|
Smart Key Unit. Schematic Diagrams
Circuit Diagram ...Smart Key Diagnostic. Repair procedures
Inspection Self Diagnosis With Scan Tool It will be able to diagnose defects of SMART KEY system with GDS quickly. GDS can operates actuator forcefully, input/output value monitoring and self diagnosis. ...See also:
Instrument Cluster. Schematic
Diagrams
Circuit Diagram ...
Manual heating and air conditioning
The heating and cooling system can be controlled manually by pressing buttons or turning knob(s) other than the AUTO button. In this case, the system works sequentially according to the order of buttons ...
Resetting the sunroof
Whenever the vehicle battery is disconnected or discharged, you must reset your sunroof system as follows: 1.Turn the ignition switch to the ON position. 2.Close the sunshade and sunroof completely if ...