Hyundai Santa Fe (DM): Specifications
Specifications
|
Item |
Specifications |
|
|
Transaxle type |
A6MF2 |
|
|
Engine model |
Gasoline 2.4GDI |
|
|
Torque converter type |
3-element, 1-stage, 2-phase type |
|
|
Torque converter size |
Ø236 mm (9.2913 in.) |
|
|
Oil pump system |
Parachoid |
|
|
Friction elements |
Clutch: 2EA |
|
|
Brake: 3EA |
||
|
OWC : 1EA |
||
|
Planetary gear |
3EA |
|
|
Gear ration |
1st |
4.639 |
|
2nd |
2.826 |
|
|
3rd |
1.841 |
|
|
4th |
1.386 |
|
|
5th |
1.000 |
|
|
6th |
0.772 |
|
|
Reverse |
3.385 |
|
|
Final gear ratio |
3.648 |
|
|
Fluid pressure balance piston |
2EA |
|
|
Accumulator |
4EA |
|
|
Solenoid valve |
8EA (VFS:6EA, ON/OFF:2EA) |
|
|
Shift lever position |
4 Range (P,R,N,D) |
|
|
Oil filter |
1EA |
|
VFS: Variable Force Solenoid
Sensors
Input Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
|
Operation condition (°C)°F |
((-)40 ~ 150)) -40 ~ 302 |
|
|
Air gap(mm)in. |
(0.95 ~ 1.65) 0.0374 ~ 0.0649 |
|
|
Output voltage(V) |
High |
1.18 ~ 1.68 |
|
Low |
0.59 ~ 0.84 |
|
Output Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
|
Operation condition (°C)°F |
((-)40 ~ 150)) -40 ~ 302 |
|
|
Air gap(mm)in. |
(0.25 ~ 0.70) 0.0098 ~ 0.0276 |
|
|
Output voltage (V) |
High |
1.18 ~ 1.68 |
|
Low |
0.59 ~ 0.84 |
|
Oil Temperature Sensor
▷ Type: Negative thermal coefficient type
▷ Specifications
|
Temp.(°C)°F |
Resistance (kΩ) |
|
(-40)-40 |
48.1 |
|
(-20)-4.0 |
15.6 |
|
(0)32.0 |
5.88 |
|
(20)68.0 |
2.51 |
|
(40)104.0 |
1.11 |
|
(60)140.0 |
0.61 |
|
(80)176.0 |
0.32 |
|
(100)212.0 |
0.18 |
|
(120)248.0 |
0.10 |
|
(140)284.0 |
0.06 |
|
(165)329.0 |
0.03 |
Inhibiter Switch
▷ Type: Combination of output signals from 4 terminals
▷ Specifications
|
Power supply (V) |
12 |
|
Output type |
Pin to Pin |
Solenoid Valves
Direct control VFS[26/B, T/CON]
▷ Control type : Normal low type
|
Control Pressure kpa (kgf/cm², psi) |
9.81 ~ 500.14 (0.1 ~ 5.1,1.42 ~ 72.54) |
|
Current value(mA) |
50 ~ 850 |
|
Internal resistance(Ω) |
5.1 |
Direct control VFS[UD/B, OD/C, 35R/C]
▷ Control Type : Normal high type
|
Control Pressure kpa (kgf/cm², psi) |
500.14 ~ 9.81 (5.1 ~ 0.1,72.54 ~ 1.42) |
|
Current value(mA) |
50 ~ 850 |
|
Internal resistance(Ω) |
5.1 |
Line Pressure Control VFS
▷ Control type : Normal high type
|
Control Pressure kpa (kgf/cm², psi) |
500.14 ~ 9.81 (5.1 ~ 0.1,72.54 ~ 1.42) |
|
Current value(mA) |
50 ~ 850 |
|
Internal resistance(Ω) |
5.1 |
ON/OFF Solenoid Valve(SS-A, SS-B)
▷ Control type : Normal low type
|
Control pressure kpa (kgf/cm², psi) |
490.33 (5.0, 71.12) |
|
Internal resistance(Ω) |
10 ~ 11 |
Solenoid Valve Operation Table
|
|
SS-A |
SS-B |
UD/B-VFS |
OD/C-VFS |
35R/C-VFS |
26/B-VFS |
|
N/H |
N/H |
N/H |
N/L |
|||
|
N, P |
● |
|
● |
|
● |
|
|
1 |
Δ |
|
|
Δ |
● |
|
|
2 |
|
|
|
● |
● |
● |
|
3 |
|
● |
|
● |
|
|
|
4 |
|
|
|
|
● |
|
|
5 |
|
● |
● |
|
|
|
|
6 |
|
|
● |
|
● |
● |
|
L |
● |
|
|
|
● |
|
|
R |
● |
● |
● |
|
|
|
● : Connected status
Δ : Connedted at vehicle speed above 8km/h
Tightening Torques
|
Item |
N.m |
Kgf.m |
lb-ft |
|
TCM installation mounting bolt/nut |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Shift cable bracket mounting bolt |
14.7 ~ 21.6 |
1.5 ~ 2.2 |
10.9 ~ 15.9 |
|
Input shaft speed sensor mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Output shaft speed sensor mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Shift lever assembly bolt |
8.8 ~ 13.7 |
0.9 ~ 1.4 |
9.4 ~ 10.8 |
|
Inhibitor switch mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Valve body cover mounting bolt |
13.7 ~ 15.7 |
1.4 ~ 1.6 |
10.1 ~ 11.6 |
|
ATF Warmer mounting bolt |
7.8 ~ 11.8 |
0.8 ~ 1.2 |
5.8 ~ 8.7 |
|
Injection hole (eyebolt) |
2.9 ~ 4.9 |
0.3 ~ 0.5 |
2.2 ~ 3.6 |
|
Oil drain plug |
38.2 ~ 48.1 |
3.9 ~ 4.9 |
28.2 ~ 35.4 |
|
Torque converter mounting bolt |
45.1 ~ 52.0 |
4.6 ~ 5.3 |
33.3 ~ 38.3 |
|
Starter motor mounting bolts |
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
Automatic transaxle upper mounting bolt (TM=>Eng) |
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
Automatic transaxle lower mounting bolt (Eng=>TM) |
42.2 ~ 48.1 |
4.3 ~ 4.9 |
31.1 ~ 35.4 |
|
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39..8 |
|
|
Automatic transaxle mounting support bracket bolt |
58.8 ~ 78.5 |
6.0 ~ 8.0 |
43.4 ~ 57.9 |
|
Automatic transaxle mounting bracket bolt |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
Lubricants
|
Item |
Specified lubricant |
Quantity |
|
Transaxle fluid |
SK ATF SP-Ⅳ, MICHANG ATF SP-Ⅳ,NOCA ATF SP-Ⅳ, Hyundai Genuine ATF SP-Ⅳ
or other brands meeting the above specification approved by Hyundai Motors
Corp. |
7.1L (1.88 U.S gal., 7.50 U.S.qt., 6.24 Imp.qt.) |
Sealant
|
Item |
Specified sealant |
|
Rear cover |
LOCTITE FMD-546 or THREE-BOND TB1281B |
|
Torque converter housing |
Special Service Tools
Special Service Tools Tools (Number and name) Illustration Use 09200-3N000 Engine support fixture(Beam) Removal and installation of the transaxle. Except lower supporter, use beam only with new engine ...
See also:
Emission control system
The emission control system of your vehicle is covered by a written limited warranty. Please see the warranty information contained in the Owner’s Handbook & Warranty Information booklet in your ...
Warning And Caution Labels
Warning And Caution Labels 1. Radiator cap caution 2. Fan caution 3. Battery caution Battery Caution Label Warning / Caution Label (Cont'd) A. Keep lighted cigarettes and all other flames or sparks ...
Driver Airbag (DAB) Module and Clock Spring. Repair procedures
Removal 1. Disconnect the battery negative cable and wait for at least three minutes before beginning work. 2. Remove the driver airbag module by putting in a flat tool (Ø5mm) into the guide hole ...
