Hyundai Santa Fe (DM): Specifications
Specification
Items |
Inner side |
Outer side |
|
Front driveshaft |
Joint type |
LSJ 104 |
UBJ 104 |
Max. permissible angle |
23.5° |
46.5° |
|
Rear driveshaft |
Joint type |
TJ |
BJ |
Max. permissible angle |
23.5° |
46.5° |
|
Rear differential |
Oil type |
Hypoid gear oil API GL-5, SAE 75W/90 (SHELL SPIRAX X or equivalent) |
|
OIL capacity |
0.53 ± 0.05L |
||
Gear type |
Hypoid |
||
Diff ratio |
2.533 |
||
Hypoid gear backlash |
0.07 ~ 0.15 mm (0.0028 ~ 0.0059 in.) |
||
Diff gear backlash |
0 ~ 0.05 mm (0 ~ 0.0020 in.) |
Items |
N.m |
kgf.m |
lb-ft |
|
Front |
Tire wheel lug nuts |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
Driveshaft castle nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
Strut assembly lower mounting bolt |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
Brake caliper mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.8 ~ 72.3 |
|
Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
Brake disc mounting screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
Hub assembly mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.8 ~ 72.3 |
|
Upper roll rod bracket bolt |
(A) 107.9 ~ 125.5 |
11.0 ~ 13.0 |
79.6 ~ 94.0 |
|
(B) 49.0 ~ 63.7 |
5.0 ~ 6.5 |
36.2 ~ 47.0 |
||
Lower arm ball joint mounting bolt |
98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
|
Tie rod end ball joint mounting nut |
34.3 ~ 44.1 |
3.5 ~ 4.5 |
25.3 ~ 32.5 |
|
Rear |
Tire wheel lug nuts |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
Driveshaft castle nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
Shock absorber lower mounting nut |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
Brake caliper mounting bolt |
49.0 ~ 58.8 |
5.0 ~ 6.0 |
36.2 ~ 43.4 |
|
Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
Brake disc mounting screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
Hub assembly mounting bolt |
78.5 ~ 88.3 |
8.0 ~ 9.0 |
57.9 ~ 65.1 |
|
Upper arm mounting bolt |
2WD : 137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
4WD : 98.1 ~ 117.7 |
10.0 ~ 12.0 |
72.3 ~ 86.8 |
||
Lower arm mounting bolt |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
Assist arm ball joint mounting nut |
137.2 ~ 156.9 |
14.0 ~ 16.0 |
101.2 ~ 115.7 |
|
Trailing arm mounting bolt |
34.3 ~ 53.9 |
3.5 ~ 5.5 |
25.3 ~ 39.7 |
|
propeller shaft |
Front propeller shaft mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
Propeller shaft center bearing bracket mounting bolt |
49.0 ~ 53.9 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
Rear Differential |
Rear propeller shaft mounting bolt |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
Rear differential mounting bolt |
68.6 ~ 88.3 |
7.0 ~ 9.0 |
50.6 ~ 65.1 |
|
Differential cover mounting bolt |
39.2 ~ 49.0 |
4.0 ~ 5.0 |
28.9 ~ 36.2 |
|
Rear differential drain plug |
49.0 ~ 68.6 |
5.0 ~ 7.0 |
36.2 ~ 50.6 |
|
Rear differential filler plug |
39.2 ~ 58.8 |
4.0 ~ 6.0 |
28.9 ~ 43.3 |
Lubricants
Items |
Lubricants |
Quantity |
||
Front driveshaft |
UBJ 104 |
Theta 2.0 T-GDI / MT |
RBA |
165 ± 10g |
Theta 2.4 GDI / MT, AT |
RBA |
150 ± 10g |
||
LSJ 104 |
Theta 2.0 T-GDI / MT |
SH06-VX21 |
250 ± 15g |
|
Theta 2.4 GDI / MT, AT |
SH06-VX21 |
215 ± 15g |
||
Rear driveshaft |
EBJ79 |
NTG2218-M |
60 ± 10g |
|
EDJ82 |
NKG205 |
80 ± 10g |
Special Service Tools
Special Service Tools Tool(Number and Name) Illustration Use 09495-33000 Puller Removal of spider assembly from a drive shaft. 09568-4A000 Ball joint puller Remove the ball joint 09495-3K000 Band installer ...See also:
Description and Operation
Description Exhaust emissions (CO, HC, NOx) are controlled by a combination of engine modifications and the addition of special control components. Modifications to the combustion chamber, intake manifold, ...
Parking Brake Assembly. Repair procedures
Removal Parking Brake Shoe 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the rear tire and wheel. 3. Remove the rear brake caliper and Rear disc brake. 4. Remove the parking brake ...
DBC Switch. Repair procedures
Inspection 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the crash pad lower panel. 3. Remove the crash pad side switch assembly (A) after loosening the screws. 4. ...