Hyundai Santa Fe (DM): Specifications - General Information - Engine Electrical SystemHyundai Santa Fe (DM): Specifications

Specification

Ignition System
Ignition Coil
Item
Specification
Primary Coil Resistance (Ω)
0.62 ± 10% [20°C (68°F)]
Secondary Coil Resistance (kΩ)
7.0 ± 15% [20°C (68°F)]

Spark plug
Item
Specification
Type
FXU16HR11
Gap
1.0 ~1.1 mm
(0.0394 ~ 0.0433 in.)

Condenser
Item
Specification
Capacitance (uF)
0.47 [1KHz]
Insulation resistance (mΩ)
1,000 [DC 500 V/1 Min]

Charging System
Alternator
Item
Specification
Rated voltage
13.5V, 130A
Speed in use
1,000 ~ 18,000 rpm
Voltage regulator
IC Regulator built-in type
Regulator Setting Voltage
External mode
Refer to below graph
Internal mode
14.55 ± 0.3V
Temperature Gradient
External mode
0 ± 3 mV / °C 
Internal mode
-3.5 ± 2mV / °C

※ Regulator Setting Voltage (External mode)
Battery
Item
Specification
Model type
CMF68L-BCI
Capacity [20HR/5HR] (AH)
68 / 54
Cold Cranking Amperage (A)
600 (SAE) / 480 (EN)
Reserve Capacity (Min)
110

•
Model type description

•
Cold Cranking Ampere (CCA): Cold Cranking Amps is a rating used in the battery industry to define a battery's ability to start an engine in cold temperatures.
-
The rating is the number of amps a new, fully charged battery can deliver at -18 °C(-0.4 °F) for 30 seconds, while maintaining a voltage of at least 7.2 volts for a 12 volt battery.
-
The higher the CCA rating, the greater the starting power of the battery.
•
RESERVE CAPACITY (RC) : Reserve Capacity is a battery industry rating, defining a battery's ability to power a vehicle with an inoperative alternator or fan belt.
-
The rating is the number of minutes a battery at 26.7 °C(80 °F) can be discharged at 25 amps and maintain a voltage of 10.5 volts for a 12 volt battery.
-
The higher the reserve rating, the longer your vehicle can operate should your alternator or fan belt fail.
Starting System
Starter
Item
Specification
Rated voltage
12 V, 1.2 kW
The number of pinion teeth
11
Performance
[No-load, 11 V]
Ampere
Max. 70 A
Speed
Min. 2,400 rpm


Tightening Torques

Item
N.m
kgf.m
lb-ft
Ignition coil installation bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Spark plug installation
14.7 ~ 24.5
1.5 ~ 2.5
10.9 ~ 18.1
Condenser & Hanger bracket installation bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Alternator installation bolt
49.0 ~ 63.7
5.0 ~ 6.5
36.2 ~ 47.0
Battery (+) terminal installation nut
7.8 ~ 9.8
0.8 ~ 1.0
5.2 ~ 8.7
Battery (-) terminal l installation nut
3.9 ~ 5.9
0.4 ~ 0.6
2.9 ~ 4.3
Battery mounting bracket installation bolt
8.8 ~ 13.7
0.9 ~1.4
6.5 ~ 10.1
Battery tray installation bolt
8.8 ~ 13.7
0.9 ~1.4
6.5 ~ 10.1
Battery sensor cable installation bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Starter installation bolt
49.0 ~ 63.7
5.0 ~ 6.5
36.2 ~ 47.0


Troubleshooting
Troubleshooting Ignition System Symptom Suspect Area Remedy Engine will not start or is hard to start (Cranks OK) Ignition lock switch Inspect ignition lock switch, or replace as required Ignition coil ...

See also:

Under Body. Body Repair
Under Body (2WD) Projected Dimensions * These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] Actual-Measurement Dimensions * These dimensions indicated in this ...

Malfunction Indicator Lamp (MIL)
This warning light illuminates: Once you set the ignition switch or Engine Start/Stop Button to the ON position. - It remains on until the engine is started. When there is a malfunction with the emission ...

Schematic Diagrams
Circuit Diagram (1) Circuit Diagram (2) ...