Hyundai Santa Fe (DM): SS-A Solenoid Valve(ON/OFF). Repair procedures - Automatic Transaxle Control System - Automatic Transaxle SystemHyundai Santa Fe (DM): SS-A Solenoid Valve(ON/OFF). Repair procedures

Inspection

1.
Turn ignition switch OFF.
2.
Remove the air duct.
3.
Disconnect the solenoid valve connector(A).
4.
Measure resistance between sensor signal terminal and sensor ground terminal.
5.
Check that the resistance is within the specification.

Removal

1.
Remove the air duct.
2.
Remove the battery and the battery tray.
3.
Remove the under cover(A).
Tightening torque :
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

4.
Drain the coolant.
5.
Remove the drain plug (A) and reinstall the drain plug after draining ATF totally.
Drain plug tightening torque:
38.2 ~ 48.1 N.m (3.9 ~ 4.9 kgf.m, 28.2 ~ 35.4 lb-ft)

Replace the gasket before reinstalling the drain plug.
6.
Remove the wiring bracket installation bolt (A).
7.
Remove the ATF Injection hole(eyebolt)(A).
Eyebolt tightening torque:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)

Replace the O-Ring (A) before reinstalling the eyebolt.
8.
Disconnect the coolant hose (B) after removing the coolant hose clamp (A).
9.
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

When hose&pipe assembly
Align marking of pipe(B), marking of hose(A), and matching color each other.
10.
Remove the valve body cover (A).
Tightening torque:
(A) 13.7~ 15.7N.m (1.4 ~ 1.6 kgf.m, 10.1 ~ 11.6lb-ft)

•
Replace the gasket (A) before reinstalling the valve body cover.

11.
Remove the bolts (C) after disconnecting the solenoid valve connector (B) and the oil temperature sensor connector (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

12.
Remove the solenoid valve support bracket (A).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

13.
Remove the solenoid valve (A).

•
When installing, apply the ATF oil or white vaseline to the O-ring (A) not to be damaged.


Installation

1.
Install in the reverse order of removal.
•
Adding coolant.
•
Adding Automatic Transaxle Fluid(ATF).
•
Perform Transaxle Control Module(TCM) learning after replacing the valve body to prevent slow transaxle response, jerky acceleration and jerky startup.

SS-A Solenoid Valve(ON/OFF). Schematic Diagrams
Circuit Diagram ...

SS-B Solenoid Valve(ON/OFF). Description and Operation
Description SS-B solenoid valve is attached to the valve body and is an on/off solenoid valve that is used to change gears. SS-B Solenoid valve(ON/OFF) is installed at valve body. ...

See also:

Side curtain
To use the side curtain: 1. Lift the curtain by the hook (1). 2. Hang the curtain on both sides of the hook. ...

California perchlorate notice
Perchlorate Material-special handling may apply, See www.dtsc.ca.gov/hazardouswaste/ perchlorate. Notice to California Vehicle Dismantlers: Perchlorate containing materials, such as air bag inflators, ...

Center Pillar Trim. Repair procedures
Replacement [Center pillar lower trim] (Driver's) • Put on gloves to protect your hands. • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around ...