Hyundai Santa Fe (DM): Under Body. Body Repair
Under Body (2WD)
| Projected Dimensions |
|
* These dimensions indicated in this figure are actual-measurement
dimensions. [ Unit : mm (inch) ] |
| Actual-Measurement Dimensions |
|
* These dimensions indicated in this figure are actual-measurement
dimensions. [ Unit : mm (inch) ] |
|
|
|
|
|
Front side member tooling hole (Ø25) |
Front side member tooling hole (Ø25) |
Side cover mounting hole (B/B: Ø9/Ø11) |
|
|
|
|
|
Front sub frame mounting bolt |
Front sub frame mounting hole (Ø18) |
Floor under cover mounting hole (Ø6.6) |
|
|
|
|
|
Front sub frame mounting hole (Ø11) |
Floor under cover mounting hole (Ø10) |
Center floor side member tooling hole (Ø8) |
|
|
|
|
|
Center floor side member tooling hole (Ø6.6) |
Center floor rear member tooling hole (Ø10) |
Center floor rear member tooling hole (Ø10) |
|
|
|
|
|
Side sill inner panel tooling hole (Ø9) |
Rear trailing arm mounting hole (Ø19) |
Rear sub frame mounting hole (Ø13) |
|
|
|
|
|
Rear sub frame mounting hole (Ø22) |
Rear floor side member tooling hole (Ø8) |
Rear floor side member tooling hole (Ø13) |
Under Body (4WD)
| Projected Dimensions |
|
* These dimensions indicated in this figure are actual-measurement
dimensions. [ Unit : mm (inch) ] |
| Actual-Measurement Dimensions |
|
* These dimensions indicated in this figure are actual-measurement
dimensions. [ Unit : mm (inch) ] |
|
|
|
|
|
Front side member tooling hole (Ø25) |
Front side member tooling hole (Ø25) |
Side cover mounting hole (B/B': Ø9/Ø11) |
|
|
|
|
|
Front sub frame mounting bolt |
Front sub frame mounting hole (Ø18) |
Floor under cover mounting hole (Ø6.6) |
|
|
|
|
|
Front sub frame mounting hole (Ø11) |
Floor under cover mounting hole (Ø10) |
Center floor side member tooling hole (Ø8) |
|
|
|
|
|
Center floor side member tooling hole (Ø6.6) |
Center floor rear member tooling hole (Ø10) |
Center floor rear member tooling hole (Ø10) |
|
|
|
|
|
Side sill inner panel tooling hole (Ø9) |
Rear trailing arm mounting hole (Ø19) |
Rear sub frame mounting hole (Ø22) |
|
|
|
|
|
Rear floor cross member extension tooling hole (Ø7) |
Rear sub frame mounting bolt |
Rear floor side member tooling hole (Ø13) |
Rear Body. Body Repair
* These dimensions indicated in this figure are actual-measurement dimensions. [ Unit : mm (inch) ] Side outer panel rear corner Tail gate hinge mounting hole (Ø12) Tail gate hinge mounting hole ...
Body Panel Gaps. Body Repair
Front & Rear Dimension Side Dimension ...
See also:
Pressure Sensor. Description and Operation
Description The 4WD ECU makes a Motor Pump(Actuator) turn round for generating an oil pressure. And then it presses a multiple disk clutch and transfers the generated torque into rear wheels. Its torque ...
Roof Trim Assembly. Repair procedures
Replacement • Put on gloves to protect your hands. • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage. • ...
Antenna. Repair procedures
Inspection Antenna Cable 1. Remove the antenna jack from the audio unit and antenna. 2. Check for continuity between the center poles of antenna cable. 3. Check for continuity between the outer poles of ...
