Hyundai Santa Fe (DM): Valve Body. Repair procedures - Hydraulic System - Automatic Transaxle SystemHyundai Santa Fe (DM): Valve Body. Repair procedures

Removal

1.
Remove the air duct.
2.
Remove the battery and the battery tray.
3.
Remove the under cover(A).

Tightening torque :
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

4.
Drain the coolant.
5.
Remove the drain plug (A) and reinstall the drain plug after draining ATF totally.

Drain plug tightening torque:
38.2 ~ 48.1 N.m (3.9 ~ 4.9 kgf.m, 28.2 ~ 35.4 lb-ft)

Replace the gasket before reinstalling the drain plug.
6.
Remove the wiring bracket installation bolt (A).

7.
Remove the ATF Injection hole(eyebolt)(A).

Eyebolt tightening torque:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)

Replace the O-Ring (A) before reinstalling the eyebolt.

8.
Disconnect the coolant hose (B) after removing the coolant hose clamp (A).

9.
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

When hose&pipe assembly
Align marking of pipe(B), marking of hose(A), and matching color each other.

10.
Remove the valve body cover (A).

Tightening torque:
(A) 13.7~ 15.7N.m (1.4 ~ 1.6 kgf.m, 10.1 ~ 11.6lb-ft)

•
Replace the gasket (A) before reinstalling the valve body cover.

11.
Remove the bolts (C) after disconnecting the solenoid valve connector (B) and the oil temperature sensor connector (A).

Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

12.
Remove the valve body assembly (A).

Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)


Installation

1.
Installation is the reverse of removal.
•
Adding coolant.
•
Adding Automatic Transaxle Fluid(ATF).
•
Perform Transaxle Control Module(TCM) learning after replacing the valve body to prevent slow transaxle response, jerky acceleration and jerky startup.

Valve Body. Components and Components Location
Component Location 1. Automatic transaxle 2. Valve body assembly 1. Pressure Control Valve(PCV) adjust screw 2. Solenoid valve bracket 3. Oil temperature sensor 4. Line Pressure Control Solenoid Valve ...

ATF Warmer. Description and Operation
Description The ATF warmer is mounted on the valve body cover to reduce oil viscosity friction by increasing oil temperature under cold condition, which in turn improves fuel efficiency. It is serial mounted ...

See also:

Snow tires
If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your vehicle’s handling ...

Manifold Absolute Pressure Sensor (MAPS). Specifications
Specification Pressure [kPa (kgf/cm², psi)] Output Voltage (V) 20.0 (0.20, 2.9) 0.79 46.7 (0.47, 6.77) 1.84 101.3 (1.03, 14.7) 4.0 ...

Front Lower Arm. Repair procedures
Removal 1. Remove the front wheel and tire (A) from front hub . Tightening torque: 88.2 ~ 107.8 N.m (9.0 ~ 11.0 kgf.m, 65.0 ~ 79.5 lb-ft) Be careful not to damage to the hub bolts when removing the front ...