Hyundai Santa Fe (TM): General Tightening Torque Table - General InformationHyundai Santa Fe (TM): General Tightening Torque Table

Tightening Torque Table of Standard Parts
BOLT (Nominal diameter)
NUT (Nominal diameter)


BOLT/NUT Normal screw
Torque Nm (kg.m, Ib-ft)

Nominal diameter.
(mm)
Pitch [mm (in.) ]
4T
8T
10T

M5
0.8 (0.031)
2.0 - 3.0 (0.2 - 0.3, 1.4 - 2.2)
4.9 - 6.9 (0.5 - 0.7, 3.6 - 5.1)
7.8 - 10.8 (0.8 - 1.1, 5.8 - 8.0)
M6
1 (0.039)
2.9 - 4.9 (0.3 - 0.5, 2.2 - 3.6) 
8.8 - 12.7 (0.9 - 1.3, 6.5 - 9.4) 
13.7 - 18.6 (1.4 - 1.9, 10.1 - 13.7)
M8
1.25 (0.049)
8.8 - 11.8 (0.9 - 1.2, 6.5 - 8.7)
22.6 - 30.4 (2.3 - 3.1, 16.6 - 22.4) 
33.3 - 44.1 (3.4 - 4.5, 24.6 - 32.5)
M10
1.5 (0.059)
16.7 - 22.6 (1.7 - 2.3, 12.3 - 16.6)
45.1 - 60.8 (4.6 - 6.2, 33.3 - 44.8)
65.7 - 88.3 (6.7 - 9.0, 48.5 - 65.1)
M12
1.75 (0.068)
29.4 - 39.2 (3.0 - 4.0, 21.7 - 28.9)
78.5 - 105.9 (8.0 - 10.8, 57.9 - 78.1)
114.7 - 154.9 (11.7 - 15.8, 84.6 - 114.3)
M14
2 (0.078)
47.1 - 63.7 (4.8 - 6.5, 34.7 - 47.0)
125.5 - 169.7 (12.8 - 17.3, 92.6 - 125.1)
183.4 - 249.1 (18.7 - 25.4, 135.3 - 183.7)
M16
2 (0.078)
73.5 - 100.0 (7.5 - 10.2, 54.2 - 73.8)
197.1 - 266.7 (20.1 - 27.2, 145.4 - 196.7)
288.3 - 390.3 (29.4 - 39.8, 212.7 - 287.9)
M20
2.5 (0.098)
144.2 - 195.2 (14.7 - 19.9, 106.3 - 143.9)
396.2 - 535.4 (40.4 - 54.6, 292.2 - 394.9)
565.8 - 764.9 (57.7 - 78.0, 417.3 - 564.2)
M24
3 (0.118)
249.1 - 337.3 (25.4 - 34.4, 183.7 - 248.8)
687.4 - 929.7 (70.1 - 94.8, 507.0 - 685.7)
975.8 - 1320.0 (99.5 - 134.6, 719.7 - 973.6)
M30
3.5 (0.137)
499.2 - 674.7 (50.9 - 68.8, 368.2 - 497.6)
1372.9 - 1858.4 (140.0 - 189.5, 1012.6 - 1370.7)
1956.4 - 2647.8 (199.5 - 270.0, 1443.0 - 1952.9)

BOLT/NUT Thin screw
Torque Nm (kg.m, Ib-ft)
Nominal diameter.
(mm)
Pitch [mm (in.) ]
4T
8T
10T

M5
0.5 (0.019)
2.0 - 3.0 (0.2 - 0.3, 1.4 - 2.2)
5.9 - 8.8 (0.6 - 0.9, 4.3 - 6.5)
8.8 - 12.7 (0.9 - 1.3, 6.5 - 9.4)
M6
0.75 (0.029)
3.9 - 4.9 (0.4 - 0.5, 2.9 - 3.6)
9.8 - 13.7 (1.0 - 1.4, 7.2 - 10.1)
14.7 - 20.6 (1.5 - 2.1, 10.8 - 15.2)
M8
1 (0.039)
8.8 - 11.8 (0.9 - 1.2, 6.5 - 8.7)
24.5 - 32.4 (2.5 - 3.3, 18.1 - 23.9)
35.3 - 48.1 (3.6 - 4.9, 26.0 - 35.4)
M10
1.25 (0.049)
17.7 - 23.5 (1.8 - 2.4, 13.0 - 17.4)
47.1 - 63.7 (4.8 - 6.5, 34.7 - 47.0)
69.6 - 94.1 (7.1 - 9.6, 51.4 - 69.4)
M12
1.25 (0.049)
32.4 - 44.1 (3.3 - 4.5, 23.9 - 32.5)
86.3 - 117.7 (8.8 - 12.0, 63.7 - 86.8)
127.5 - 172.6 (13.0 - 17.6, 94.0 - 127.3)
M14
1.5 (0.059)
51.0 - 69.6 (5.2 - 7.1, 37.6 - 51.4)
136.3 - 185.3 (13.9 - 18.9, 100.5 - 136.7)
201.0 - 271.6 (20.5 - 27.7, 148.3 - 200.4)
M16
1.5 (0.059)
79.4 - 107.9 (8.1 - 11.0, 58.6 - 79.6)
211.8 - 286.4 (21.6 - 29.2, 156.2 - 211.2)
311.8 - 421.7 (31.8 - 43.0, 230.0 - 311.0)
M20
1.5 (0.059)
163.8 - 221.6 (16.7 - 22.6, 120.8 - 163.5)
448.2 - 607.0 (45.7 - 61.9, 330.5 - 447.7)
639.4 - 864.9 (65.2 - 88.2, 471.6 - 638.0)
M24
2 (0.078)
276.5 - 373.6 (28.2 - 38.1, 204.0 - 275.6)
759.0 - 1026.8 (77.4 - 104.7, 559.8 - 757.3)
1080.7 - 1462.2 (110.2 - 149.1, 797.1 - 1078.4)
M30
2 (0.078)
562.9 - 762.0 (57.4 - 77.7, 415.2 - 562.0)
1553.4 - 2102.5 (158.4 - 214.4, 1145.7 - 1550.8)
2210.4 - 2991.0 (225.4 - 305.0, 1630.3 - 2206.1)

Flange BOLT (Nominal diameter)
Flange NUT (Nominal diameter)


Flange BOLT/NUT Normal screw
Torque Nm (kg.m, Ib-ft)
Nominal diameter.
(mm)
Pitch [mm (in.) ]
4T
8T
10T

M5
0.8 (0.031)
2.0 - 2.9 (0.2 - 0.3, 1.4 - 2.2)
5.9 - 7.8 (0.6 - 0.8, 4.3 - 5.8)
8.8 - 11.8 (0.9 - 1.2, 6.5 - 8.7)
M6
1 (0.039)
3.9 - 4.9 (0.4 - 0.5, 2.9 - 3.6)
9.8 - 13.7 (1.0 - 1.4, 7.2 - 10.1)
14.7 - 19.6 (1.5 - 2.0, 10.8 - 14.5)
M8
1.25 (0.049)
8.8 - 11.8 (0.9 - 1.2, 6.5 - 8.7)
24.5 - 32.4 (2.5 - 3.3, 18.1 - 23.9)
35.3 - 48.1 (3.6 - 4.9, 26.0 - 35.4)
M10
1.5 (0.059)
17.7 - 24.5 (1.8 - 2.5, 13.0 - 18.1)
48.1 - 65.7 (4.9 - 6.7, 35.4 - 48.5)
70.6 - 96.1 (7.2 - 9.8, 52.1 - 70.9)
M12
1.75 (0.068)
31.4 - 43.1 (3.2 - 4.4, 23.1 - 31.8)
84.3 - 113.8 (8.6 - 11.6, 62.2 - 83.9)
123.6 - 167.7 (12.6 - 17.1, 91.1 - 123.7)
M14
2 (0.078)
51.0 - 68.6 (5.2 - 7.0, 37.6 - 50.6)
135.3 - 182.4 (13.8 - 18.6, 99.8 - 134.5)
198.1 - 268.7 (20.2 - 27.4, 146.1 - 198.2)
M16
2 (0.078)
79.4 - 107.9 (8.1 - 11.0, 58.6 - 79.6)
212.8 - 288.3 (21.7 - 29.4, 157.0 - 212.7)
311.8 - 421.7 (31.8 - 43.0, 230.0 - 311.0)

Flange BOLT/NUT Thin screw
Torque Nm (kg.m, Ib-ft)

Nominal diameter.
(mm)
Pitch [mm (in.) ]
4T
8T
10T

M5
0.5 (0.019)
2.9 - 2.9 (0.3 - 0.3, 2.2 - 2.2)
6.9 - 8.8 (0.7 - 0.9, 5.1 - 6.5)
9.8 - 13.7 (1.0 - 1.4, 7.2 - 10.1)
M6
0.75 (0.029)
3.9 - 5.9 (0.4 - 0.6, 2.9 - 4.3)
10.8 - 14.7 (1.1 - 1.5, 8.0 - 10.8)
16.7 - 21.6 (1.7 - 2.2, 12.3 - 15.9)
M8
1 (0.039)
9.8 - 12.7 (1.0 - 1.3, 7.2 - 9.4)
26.5 - 35.3 (2.7 - 3.6, 19.5 - 26.0)
38.2 - 52.0 (3.9 - 5.3, 28.2 - 38.3)
M10
1.25 (0.049)
19.6 - 25.5 (2.0 - 2.6, 14.5 - 18.8)
51.0 - 68.6 (5.2 - 7.0, 37.6 - 50.6)
75.5 - 102.0 (7.7 - 10.4, 55.7 - 75.2)
M12
1.25 (0.049)
35.3 - 48.1 (3.6 - 4.9, 26.0 - 35.4)
94.1 - 126.5 (9.6 - 12.9, 69.4 - 93.3)
138.3 - 186.3 (14.1 - 19.0, 102.0 - 137.4)
M14
1.5 (0.059)
55.9 - 75.5 (5.7 - 7.7, 41.2 - 55.7)
148.1 - 200.1 (15.1 - 20.4, 109.2 - 147.6)
216.7 - 293.2 (22.1 - 29.9, 159.8 - 216.3)
M16
1.5 (0.059)
86.3 - 116.7 (8.8 - 11.9, 63.7 - 86.1)
229.5 - 309.9 (23.4 - 31.6, 169.3 - 228.6)
336.4 - 455.0 (34.3 - 46.4, 248.1 - 335.6)

  
1)
The torques shown in the table are standard values under the following conditions.
•
Nuts and bolts are made of galvanized steel bar.
•
Galvanized plain steel washers are inserted.
•
All nuts, bolts and plain washers are dry.
2)
The torques shown in the table are not applicable.
•
When spring washers, toothed washers and the like are inserted.
•
If plastic parts are fastened.
•
If self-tapping screws or self-locking nuts are used.
•
If threads and surfaces are coated with oil.
Important Safety Notice
Important Safety Notice Proper service methods and repair procedures are essential for safe, reliable operation of all motor vehicles as well as personal safety of the operator. The service procedures ...

See also:

Repair procedures
Adjustment Transaxle Control Module(TCM) Learning When shift shock is occurred or parts related with the transaxle are replaced, TCM learning should be performed. In the following case, TCM learning is ...

Rear Mud Guard. Repair procedures
Replacement • Put on gloves to protect your hands. • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage. • ...

Oil hydraulic Motor(Actuator). Repair procedures
Inspection If you have trouble code related to the oil hydraulic motor (actuator), check oil hydraulic motor (actuator) according to the inspection process. Oil Hydraulic Motor (Actuator) Inspection Procedure ...