Hyundai Santa Fe: SS-B Solenoid Valve(ON/OFF). Repair procedures - Automatic Transaxle Control System - Automatic Transaxle SystemHyundai Santa Fe: SS-B Solenoid Valve(ON/OFF). Repair procedures

Inspection

1.
Turn ignition switch OFF.
2.
Remove the air duct.
3.
Disconnect the solenoid valve connector(A).
4.
Measure resistance between sensor signal terminal and sensor ground terminal.
5.
Check that the resistance is within the specification.

Removal

1.
Remove the air duct.
2.
Remove the battery and the battery tray.
3.
Remove the under cover(A).
Tightening torque :
7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft)

4.
Drain the coolant.
5.
Remove the drain plug (A) and reinstall the drain plug after draining ATF totally.
Drain plug tightening torque:
38.2 ~ 48.1 N.m (3.9 ~ 4.9 kgf.m, 28.2 ~ 35.4 lb-ft)

Replace the gasket before reinstalling the drain plug.
6.
Remove the wiring bracket installation bolt (A).
7.
Remove the ATF Injection hole(eyebolt)(A).
Eyebolt tightening torque:
2.9 ~ 4.9 N.m (0.3 ~ 0.5 kgf.m, 2.2 ~ 3.6 lb-ft)

Replace the O-Ring (A) before reinstalling the eyebolt.
8.
Disconnect the coolant hose (B) after removing the coolant hose clamp (A).
9.
Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

When hose&pipe assembly
Align marking of pipe(B), marking of hose(A), and matching color each other.
10.
Remove the valve body cover (A).
Tightening torque:
(A) 13.7~ 15.7N.m (1.4 ~ 1.6 kgf.m, 10.1 ~ 11.6lb-ft)

•
Replace the gasket (A) before reinstalling the valve body cover.

11.
Remove the bolts (C) after disconnecting the solenoid valve connector (B) and the oil temperature sensor connector (A).
Tightening torque:
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

12.
Remove the solenoid valve support bracket (A).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

13.
Remove the solenoid valve (A).

•
When installing, apply the ATF oil or white vaseline to the O-ring (A) not to be damaged.


Installation

1.
Install in the reverse order of removal.
•
Adding coolant.
•
Adding Automatic Transaxle Fluid(ATF).
•
Perform Transaxle Control Module(TCM) learning after replacing the valve body to prevent slow transaxle response, jerky acceleration and jerky startup.

SS-B Solenoid Valve(ON/OFF). Schematic Diagrams
Circuit Diagram ...

Inhibitor Switch. Description and Operation
Description Inhibitor Switch monitors the lever's position(P, R, N, D) and is used to control gear setting signals. ...

See also:

Programming HomeLink®
✽ NOTICE When programming a garage door opener, it is advised to park the vehicle outside of the garage. It is recommended that a new battery be placed in the hand-held transmitter of the device ...

Rear Door Latch. Components and Components Location
Component Location 1. Rear door latch ...

Repair procedures
Replacement 1. Remove the cap (A) and remove the nuts, then remove the wiper arm (B). Tightening torque : 22.6 ~ 26.5 N.m(2.3 ~ 2.7 kgf.m, 16.6 ~ 19.5 lb-ft) 2. Detach the clips, then remove the fender ...