Hyundai Santa Fe (DM): Smart Key Unit. Repair procedures
Removal
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the driver crash pad lower panel.
|
3. |
Remove the smart key unit (B) after loosening the
mounting bolts(2EA) and disconnecting the connector (A).
Hvac repair services emergency response Cranford platinum hvac.
|
Take care not to scratch the crash pad and related
parts.
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the crash pad center panel.
|
3. |
Remove the RF receiver after loosening the mounting
nut (1EA) and disconnecting the connector.
|
Take care not to scratch the crash pad and related
parts.
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the crash pad center panel.
|
3. |
Remove the interior 1 antenna (B) after loosening
the mounting nuts (2EA) and disconnecting the connector (A).
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the console rear complete assembly.
|
3. |
Remove the interior 2 antenna (B) after loosening
the mounting nuts (2EA) and disconnecting the connector (A).
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the luggage covering mat (A).
|
3. |
Remove the luggage floor box (A) after loosening
the screws (4EA).
|
4. |
Remove the luggae tray box (A).
|
5. |
Remove the floor mat (A) after loosening the screws
(4EA).
|
6. |
Remove the interior 3 antenna (B) after loosening
the mounting screws(2EA) and disconnecting the connector (A).
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the rear bumper cover.
|
3. |
Disconnect the antenna connector (A) on the center
of rear bumper.
|
4. |
After loosening the nuts (2EA), remove the exterior
bumper antenna (B).
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the front left wheel guide.
|
3. |
Disconnect the connectors, then remove the buzzer
(A).
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the door outside handle cover (A) after seperating
the plug hole (B) from the door and loosening the mounting bolt.
|
3. |
Remove the outside handle (A) by sliding it rearward.
|
4. |
Disconnect the door outside handle connector (A).
|
1. |
Disconnect the negative (-) battery terminal.
|
2. |
Remove the tailgate trim.
|
3. |
Remove the tailgate back panel.
|
4. |
Loosen the tailgate switch mounting screws (2EA).
|
5. |
Remove the tailgate switch (A) after seperating the
license lamp wiring.
|
Inspection
1. |
Check for continuity between the tailgate latch terminals.
|
2. |
If continuity is not specified, inspect the switch
|
Installation
1. |
Install the smart key unit.
|
2. |
Install the smart key unit mounting bolts and connect
the connector.
|
3. |
Install the driver side crash pad lower panel.
|
4. |
Install the negative (-) battery terminal and check
the smart key system.
|
1. |
Install the RF receiver.
|
2. |
Install the RF receiver mounting nut and connect
the connector.
|
3. |
Install the crash pad center panel.
|
4. |
Install the negative (-) battery terminal and check
the smart key system.
|
1. |
Install the interior 1 antenna.
|
2. |
Install the crash pad center panel.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
1. |
Install the interior 2 antenna.
|
2. |
Install the console rear complete assembly.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
1. |
Install the interior 3 antenna.
|
2. |
Install the floor mat, the luggage tray box, the
luggage floor box and luggage covering mat.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
1. |
Install the exterior bumper antenna.
|
2. |
Install the rear bumper cover.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
1. |
Install the buzzer.
|
2. |
Install the front left wheel guide.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
1. |
Install the outside handle.
|
2. |
Install the door trim.
|
3. |
Install the negative (-) battery terminal and check
the smart key system.
|
1. |
Install the tailgate switch.
|
2. |
Install the tailgate garnish.
|
3. |
Install the tailgate trim.
|
4. |
Install the negative (-) battery terminal and check
the smart key system.
|
Smart Key Unit. Schematic Diagrams
Circuit Diagram ...Smart Key Diagnostic. Repair procedures
Inspection Self Diagnosis With Scan Tool It will be able to diagnose defects of SMART KEY system with GDS quickly. GDS can operates actuator forcefully, input/output value monitoring and self diagnosis. ...See also:
Lumbar support (for driver’s seat)
The lumbar support can be adjusted by pressing the switch. 1. Press the front portion (1) of the switch to increase support, or the rear portion (2) of the switch, to decrease support. 2. Release the ...
Important Safety Notice
Important Safety Notice Proper service methods and repair procedures are essential for safe, reliable operation of all motor vehicles as well as personal safety of the operator. The service procedures ...
Checking tire inflation pressure
Check your tires once a month or more. Also, check the tire pressure of the spare tire. How to check Use a good quality gage to check tire pressure.You can not tell if your tires are properly inflated ...