Hyundai Santa Fe: Balance Shaft & Oil Pump. Repair procedures - Lubrication System - Engine Mechanical SystemHyundai Santa Fe: Balance Shaft & Oil Pump. Repair procedures

Removal

1.
Remove the timing chain.
2.
Install a stopper pin (A) after compressing the balance shaft chain tensioner.
3.
Remove the balance shaft chain hydraulic tensioner (B).
4.
Remove the balance shaft chain tensioner arm (C).
5.
Remove the balance shaft chain guide (D).
https://www.fantorg.ru/shop/dvp-orgalit оргалит купить стройматериалы в мытищах.

6.
Remove the balance shaft & oil pump module (A), the balance shaft chain (B) and the sprocket (C).

Do not disassemble the balance shaft & oil pump module.

Installation

1.
The key of crankshaft should be aligned with the mating face of main bearing cap. As a result of this, the piston of No.1 cylinder is placed at the top dead center on compression stroke.
2.
Confirm the balance shaft & oil pump module timing mark.
Timing marks to be visually aligned with centers of adjacent cast timing notches.
3.
Install the balance shaft & oil pump module (A) with the chain (B) and the sprocket (C).

The timing marks of balance shaft & oil pump module sprocket and crankshaft sprocket should be matched with the timing marks (color link) of balance shaft chain.

Tightening order
(1)
Tighten the bolts in order number as shown with seating torque 26.4 N.m (3.0kgf.m, 21.7 lb-ft) and then loosen the bolts as reverse tightening order. (6-5-4-3-2-1).
(2)
Using the SST (09221-4A000), tighten the bolts as specified tightening order in same increments as follows.
Tightening torque
Bolts (A) (M9x181.5) :
22.6 ~ 26.5 N.m (2.3 ~ 2.7 kgf.m, 16.6 ~ 19.5 lb-ft) + 88 ~ 92°
Bolts (B) (M9x95) :
22.6 ~ 26.5 N.m (2.3 ~ 2.7 kgf.m, 16.6 ~ 19.5 lb-ft) + 43 ~ 47°

4.
Install the balance shaft chain guide (D).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
5.
Install the balance shaft chain tensioner arm (C).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)
6.
Install the balance shaft chain hydraulic tensioner (B) then remove the stopper pin (A).
Tightening torque :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

7.
Confirm the timing marks.
8.
Remove the stopper pin (A) of balance shaft module.
9.
Install the timing chain.

Balance Shaft & Oil Pump. Components and Components Location
Components 1. Balance shaft & oil pump assembly 2. Balance shaft chain tensioner 3. Balance shaft chain 4. Balance shaft chain sprocket 5. Balance shaft chain guide 6. Balance shaft chain tensioner ...

Oil Pressure Switch. Repair procedures
Inspection 1. Check the continuity between the terminal and the body with an ohmmeter. If there is no continuity, replace the oil pressure switch. 2. Check the continuity between the terminal and the body ...

See also:

Interior overview
1. Inside door handle 2. Outside rearview mirror control 3. Power window lock button 4. Central door lock switch 5. Power window switch 6. Fuel-filler lid opener 7. Instrument panel illumination control ...

Oil hydraulic Motor(Actuator). Description and Operation
Description The 4WD ECM controls the Pump Motor Pump (Actuator) to generating an oil pressure. The pressure engages a multiple disk clutch to transfer torque to the rear wheels. The torque to the rear ...

Caring for disc
If the temperature inside the car is too high, open the car windows to ventilate before using the system. It is illegal to copy and use MP3/WMA files without permission. Use CDs that are created only ...