Hyundai Santa Fe: ETC (Electronic Throttle Control) System. Specifications
Specification
|
Throttle Angle(°) |
Output Voltage(V) |
|
|
TPS1 |
TPS2 |
|
|
0 |
0.0 |
5.0 |
|
10 |
0.48 |
4.52 |
|
20 |
0.95 |
4.05 |
|
30 |
1.43 |
3.57 |
|
40 |
1.90 |
3.10 |
|
50 |
2.38 |
2.62 |
|
60 |
2.86 |
2.14 |
|
70 |
3.33 |
1.67 |
|
80 |
3.81 |
1.19 |
|
90 |
4.29 |
0.71 |
|
100 |
4.76 |
0.24 |
|
105 |
5.0 |
0 |
|
C.T (6 ~ 15°) |
0.29 ~ 0.71 |
4.29 ~ 4.71 |
|
W.O.T (93 ~ 102°) |
4.43 ~ 4.86 |
0.14 ~ 0.57 |
|
Item |
Sensor Resistance(kΩ) |
|
TPS1 |
0.875 ~ 1.625 [20°C(68°F)] |
|
TPS2 |
0.875 ~ 1.625 [20°C(68°F)] |
|
Item |
Specification |
|
Coil Resistance (Ω) |
1.2 ~ 1.8 [20°C(68°F)] |
ETC (Electronic Throttle Control) System. Troubleshooting
Fail-Safe Mode Item Fail-Safe ETC Motor Throttle valve stuck at 5° TPS TPS 1 fault ECM looks at TPS2 TPS 2 fault ECM looks at TPS1 TPS 1,2 fault Throttle valve stuck at 5° APS APS 1 fault ECM looks at ...
ETC (Electronic Throttle Control) System. Schematic Diagrams
Circuit Diagram ...
See also:
If engine turns over normally but does not start
1. Check fuel level. 2. With the ignition switch in the LOCK position, check all connectors at ignition coils and spark plugs. Reconnect any that may be disconnected or loose. 3. If the engine still does ...
Cruise Control Switch. Repair procedures
Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the driver airbag module. <a href="content.asp?vehicletype=Passenger&mfrcode=HY&area=HMA&langcode=ENG&modelid=AN13&modelyr=2013&mmctype=ab&mmcid=36&group=SHOP&pdftype=&cat1=2013+%3E+G+2%2E0+T%2DGDI&ec=&nLocation=1$2_1_3_1&firstnodedesc=Restraint&sitinfolist=81%5E8120%5E81200100%5Enone%5E801%5E1%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%2481%5E8120%5E81200100%5Enone%5E801%5E4%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%2481%5E8120%5E81200100%5Enone%5E801%5E8%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%24" ...
Windshield Deicer Switch. Repair
procedures
Inspection 1. The windshield deicer switch inputs can be checked using the GDS. 2. To check the input value of windshield deicer switch, select option "Body Control Module". 3. Select option ...
