Hyundai Santa Fe: General Tightening Torque Table - General InformationHyundai Santa Fe: General Tightening Torque Table

General Tightening Torque Table

Bolt nominal
diameter (mm)
 Pitch (mm)
 Torque Nm (kg.cm, lb.ft)
Head Mark 4
 Head Mark 7

M5
 0.8
 3 ~ 4 (30 ~ 40, 2.2 ~ 2.9)
 5 ~ 6 (50 ~ 60, 3.6 ~ 4.3)
M6
 1.0
 5 ~ 6 (50 ~ 50, 3.6 ~ 4.3)
 9 ~ 11 (90 ~ 110, 6.5 ~ 8.0)
M8
 1.25
 12 ~ 15 (120 ~ 150, 9 ~ 11)
 20 ~ 25 (200 ~ 250, 14.5 ~ 18.0 )
M10
 1.25
 25 ~ 30 (250 ~ 300, 18 ~ 22)
 30 ~ 50 (300 ~ 500, 22 ~ 36)
M12
 1.25
 35 ~ 45 (350 ~ 450, 25 ~ 33)
 60 ~ 80 (600 ~ 800, 43 ~ 58)
M14
 1.5
 75 ~ 85 (750 ~ 850, 54 ~ 61)
 120 ~ 140 (1,200 ~ 1,400, 85 ~ 100)
M16
 1.5
 110 ~ 130 (1,100 ~ 1,300, 80 ~ 94)
 180 ~ 210 (1,800 ~ 2,100, 130 ~ 150)
M18
 1.5
 160 ~ 180 (1,600 ~ 1,800, 116 ~ 130)
 260 ~ 300 (2,600 ~ 3,000, 190 ~ 215)
M20
 1.5
 220 ~ 250 (2,200 ~ 2,500, 160 ~ 180)
 360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
M22
 1.5
 290 ~ 330 (2,900 ~ 3,300, 210 ~ 240)
 480 ~ 550 (4,800 ~ 5,500, 350 ~ 400)
M24
 1.5
 360 ~ 420 (3,600 ~ 4,200, 260 ~ 300)
 610 ~ 700 (6,100 ~ 7,000, 440 ~ 505)

1.
The torques shown in the table are standard values under the following conditions.
•
Nuts and bolts are made of galvanized steel bar.
•
Galvanized plain steel washers are inserted.
•
All nuts, bolts and plain washers are dry.
2.
The torques shown in the table are not applicable.
•
When spring washers, toothed washers and the like are inserted.
•
If plastic parts are fastened.
•
If self-tapping screws or self-locking nuts are used.
•
If threads and surfaces are coated with oil.
3.
Reduce the torque values to the indicated percentage of the standard value under the following conditions.
•
If spring washers are used : 85%
•
If threads and bearing surfaces are stained with oil : 85%

Towing
Towing If the vehicle needs to be towed, call a professional towing service. Never tow vehicle with just a rope or chain. It is very dangerous. [Front] [Rear] Emergency Towing There are three popular methods ...

Basic Service Symbols
Basic Service Symbols There are five primary symbols used to complement illustrations. These symbols indicate the part to apply such materials during service. Symbol Meaning Do not reuse the part. Replace ...

See also:

SS-A Solenoid Valve(ON/OFF). Description and Operation
Description SS-A solenoid valve is attached to the valve body and is an on/off solenoid valve that is used to change gears. SS-A Solenoid valve(ON/OFF) is installed at valve body. ...

Crankshaft Position Sensor (CKPS). Schematic Diagrams
Circuit Diagram ...

ATF Warmer. Repair procedures
Removal 1. Drain the coolant. 2. Remove the air cleaner assembly and air duct. 3. Remove the battery and battery tray. 4. Remove the under cover(A). Tightening torque : 7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, ...