Hyundai Santa Fe: Parking Brake Lever Assembly. Repair procedures - Parking Brake System - Brake SystemHyundai Santa Fe: Parking Brake Lever Assembly. Repair procedures

Hyundai Santa Fe DM 2013-2018 Service Manual / Brake System / Parking Brake System / Parking Brake Lever Assembly. Repair procedures

Removal

The parking brake cables must not be bent or distorted. This will lead to stiff operation and premature failure.
1.
Remove the floor console assembly.
2.
Disconnect the connector (A) of parking brake switch.
3.
Loosen the adjusting nut (A) and the parking brake cables (B).

Parking brake lever in the car must be in fully loosened position.
4.
Remove the parking brake lever assembly (A) after removing the bolts.

Installation

1.
Install the parking brake lever assembly (A).
Tightening torque :
19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)

2.
Install the parking brake cable (B) and tighten the adjusting nut (A).
3.
Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.
Specified grease:
Multi purpose grease SAE J310, NLGI No.2

4.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).
Parking brake lever stroke:
5 ~ 6 clicks (Pull the lever with 196N (20 kgf, 44 lbf))
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")

5.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
6.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
7.
Reconnect the connector (A) of parking brake switch.

Inspect the continuity of parking brake switch.
When the brake lever is pulled: continuity
When the brake lever is released: no continuity
8.
Install the floor console.

Adjustment

Parking Brake Lever Stroke Adjustment
1.
Remove the floor console.
2.
Apply the brake pedal 20 times with the force of 10kgf after bleeding. Then, for the cable to settle in, apply the parking brake full stroke more than 3 times.
3.
Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).
Parking brake lever stroke :
5 ~ 6 clicks (Pull the lever with 196N (20 kgf, 44 lbf))
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke. (Refer to "Parking brake shoe installation")
4.
Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
5.
Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
6.
Install the floor console.

Parking Brake Assembly. Repair procedures
Removal Parking Brake Shoe 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the rear tire and wheel. 3. Remove the rear brake caliper and Rear disc brake. 4. Remove the parking brake ...

Parking Brake Pedal Assembly. Repair procedures
Removal 1. Turn ignition switch OFF and disconnect the negative (-) battery cable. 2. Remove the crash pad lower panel. 3. Remove the junction box. 4. Disconnect the parking brake switch connector. 5. ...

See also:

Instrument Cluster. Components and Components Location
Components Connector Pin Information No. Description No. Description 1 - 21 - 2 Illumination output 22 - 3 Rheostat down switch 23 4P output 4 Rheostat up switch 24 Immobilizer 5 AT N output 25 AT S output ...

Emergency towing
Rear If towing is necessary, we recommend you to have it done by an authorized HYUNDAI dealer or a commercial tow truck service. If towing service is not available in an emergency, your vehicle may be ...

Components and Components Location
Components Location 1. PCV Valve 2. Canister 3. Purge Control Solenoid Valve (PCSV) 4. Fuel Tank Pressure Sensor (FTPS) 5. Canister Close Valve (CCV) 6. Fuel Level Sender (FLS) 7. Fuel Tank Air Filter ...