Hyundai Santa Fe: Repair procedures

Hyundai Santa Fe DM 2013-2018 Service Manual / Engine Mechanical System / Cylinder Block / Repair procedures

Disassembly

•	Use fender covers to avoid damaging painted surfaces.

•	To avoid damage, unplug the wiring connectors carefully while holding the connector portion.

•	Mark all wiring and hoses to avoid misconnection.

•	Turn the crankshaft pulley so that the No.1 piston is at top dead center.

•	Engine removal is required for this procedure.

In case of removing the high pressure fuel pump, high pressure fuel pipe, delivery pipe, and injector, there may be injury caused by leakage of the high pressure fuel. So don’t do any repair work right after engine stops.

1.	Remove the balance shaft module.

2.	Remove the ladder frame.

3.	Remove the piston & connecting rod assembly.

4.	Remove the crankshaft.

5.	Remove the oil jet (A).

Inspection

1.	Remove gasket material. Using a gasket scraper, remove all the gasket material from the top surface of the cylinder block.

2.	Clean cylinder block Using a soft brush and solvent, thoroughly clean the cylinder block.

Inspect top surface of cylinder block for flatness.

Using a precision straight edge and feeler gauge, measure the contacting surface of the cylinder block and the manifolds for warpage..

Flatness of cylinder block gasket surface

Standard : Less than 0.05 mm (0.0019 in.) for all

Less than 0.02 mm (0.0007 in.) for 100 mm (3.9370 in.) x 100 mm (3.9370 in.)

4.	Inspect cylinder bore diameter. Visually check the cylinder for vertical scratchs. If deep scratches are present, replace the cylinder block.

Inspect cylinder bore diameter.

Using a cylinder bore gauge, measure the cylinder bore diameter at position in the thrust and axial directions.

Standard diameter :

88.00 ~ 88.03 mm (3.4645 ~ 3.4657 in.)

Measure position points (from the bottom of the cylinder block)

: 110.7 mm (4.3582 in.) / 160 mm (6.2992 in.) / 210 mm (8.2677 in.)

Check the cylinder bore size code on the cylinder block.

Cylinder Bore Inner Diameter

Size Code	Cylinder Bore Inner Diameter
A	88.00 ~ 88.01 mm (3.4645 ~ 3.4649 in.)
B	88.01 ~ 88.02 mm (3.4649 ~ 3.4653 in.)
C	88.02 ~ 88.03 mm (3.4653 ~ 3.4657 in.)

Check the piston size code on the piston top face.

Stamp the grade mark of basic diameter with rubber stamp.

Piston Outer Diameter

Size Code	Piston Outer Diameter
A	87.970 ~ 87.980 mm (3.46338 ~ 3.46377 in.)
B	87.980 ~ 87.990 mm (3.46377 ~ 3.46417 in.)
C	87.990 ~ 88.000 mm (3.46417 ~ 3.46456 in.)

Select the piston related to cylinder bore class.

Clearance : 0.020 ~ 0.040 mm (0.00079 ~ 0.00157 in.)

Reassembly

Install the oil jet (A).

Tightening torque :

24.5 ~ 29.4 N.m (2.5 ~ 3.0 kgf.m, 18.1 ~ 21.7 lb-ft)

2.	Install the crankshaft.

3.	Install the piston & connecting rod assembly.

4.	Install the ladder frame.

Ladder Frame. Repair procedures

Removal • Use fender covers to avoid damaging painted surfaces. • To avoid damage, unplug the wiring connectors carefully while holding the connector portion. • Mark all wiring and hoses to avoid ...

Piston and Connecting Rod. Components and Components Location

Components 1. Piston ring 2. Snap ring 3. Piston 4. Connecting rod 5. Connecting rod upper bearing 6. Connecting rod lower bearing 7. Connecting rod bearing cap ...