Removal
Pressure Side Impact Sensor (P-SIS)
| •
|
Removal of the airbag must be performed according to the
precautions/procedures described previously.
|
| •
|
Before disconnecting the side impact sensor connector(s),
disconnect the side airbag connector(s).
|
| •
|
Do not turn the ignition switch ON and do not connect
the battery cable while replacing the side impact sensor.
|
|
|
1. |
Disconnect the battery negative cable, and wait for at least three
minutes before beginning work.
|
|
2. |
Remove the front door trim.
|
|
3. |
Disconnect the pressure side impact sensor (A) connector and remove
the pressure side impact sensor mounting screws.
Бассейны челябинска расписание сеансов открытыи бассеи в челябинске citrusfitness.ru.
|
Rear Side Impact Sensor
|
1. |
Disconnect the battery negative cable and wait for at least three
minutes before beginning work.
|
|
2. |
Remove the luggage side trim.
|
|
3. |
Disconnect the rear side impact sensor connector.
|
|
4. |
Loosen the rear side impact sensor mounting bolt and then remove
the rear side impact sensor (A).
|
Installation
Pressure Side Impact Sensor
|
1. |
Install the new pressure side impact sensor (A) with the screws
then connect the pressure side impact sensor connector.
Tightening torque :
3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)
|
|
• |
Use the specified screws only.
|
|
|
|
2. |
Install the front door trim.
|
|
3. |
Reconnect the battery negative cable.
|
|
4. |
After installing the pressure side impact sensor, confirm proper
system operation:
| A. |
Turn the ignition switch ON; the SRS indicator light should
be turned on for about six seconds and then go off.
|
|
• |
You must comply with the specified tightening
torques with the tool specified because Pressure – Side
Impact Sensors (P-SIS) may be broken or the POP-NUT
may be rotated.
|
|
• |
Problems may be occurred in the durability of
P-SIS or impact sensing performance may be depreciated
if POP-NUT is rotated.
|
|
• |
The door module must not be transformed because
SRSCM judges a impact through the pressure sensor in
the door module.
|
|
|
Rear Side Impact Sensor
| •
|
Do not turn the ignition switch ON and do not connect
the battery cable while replacing the side impact sensor.
|
|
|
1. |
Install the new rear side impact sensor with a bolt and then connect
the rear side impact sensor connector.
Tightening torque:
6.8 ~ 9.2 N.m (0.7 ~ 0.94 kgf.m, 5.0 ~ 6.8 lb-ft)
|
|
|
2. |
Install the luggage side trim.
|
|
3. |
Reconnect the battery negative cable.
|
|
4. |
After installing the Side Impact Sensor, confirm proper system
operation:
| A. |
Turn the ignition switch ON; the SRS indicator light should
be turned on for about six seconds and then go off.
|
|
Description The SRSCM shall monitor the status of the driver and front passenger seat belt buckle. The SRSCM provides one pin each for the driver and front passenger seat belt buckle status input. The ...
See also:
Identification Numbers
Identification Number Identification Number Description Vehicle Identification Number 1. World Manufacturer Identifier (WMI) - KMF : Commercial vehicle (Van) - KMH : Passenger vehicle or MPV(Multipurpose ...
Checking the coolant level
Removing radiator cap Never attempt to remove the radiator cap while the engine is operating or hot. Doing so might lead to cooling system and engine damage and could result in serious personal injury ...
Checking the engine oil level
Type A Type B 1. Be sure the vehicle is on level ground. 2. Start the engine and allow it to reach normal operating temperature. 3. Turn the engine off and wait for a few minutes (about 5 minutes) for ...
Hyundai Santa Fe: Side Impact Sensor (SIS). Repair procedures
Side Impact Sensor (SIS). Components and Components Location
Seat Belt Buckle Switch (BS). Description and Operation