Hyundai Santa Fe (DM): Specifications - General Information - Driveshaft and axleHyundai Santa Fe (DM): Specifications

Specification

Items
 Inner side
 Outer side
Front driveshaft
 Joint type
 LSJ 104
 UBJ 104
Max. permissible angle
 23.5°
 46.5°
Rear driveshaft
 Joint type
 TJ
 BJ
Max. permissible angle
 23.5°
 46.5°
Rear differential
 Oil type
 Hypoid gear oil API GL-5, SAE 75W/90 (SHELL SPIRAX X or equivalent)
OIL capacity
 0.53 ± 0.05L
Gear type
 Hypoid
Diff ratio
 2.533
Hypoid gear backlash
 0.07 ~ 0.15 mm (0.0028 ~ 0.0059 in.)
Diff gear backlash
 0 ~ 0.05 mm (0 ~ 0.0020 in.)

Tightening torque
Items
 N.m
 kgf.m
 lb-ft
Front
 Tire wheel lug nuts
 88.3 ~ 107.9
 9.0 ~ 11.0
 65.1 ~ 79.6
Driveshaft castle nut
 240.3 ~ 269.7
 24.5 ~ 27.5
 177.2 ~ 198.9
Strut assembly lower mounting bolt
  137.2 ~ 156.9
 14.0 ~ 16.0
  101.2 ~ 115.7
Brake caliper mounting bolt
  78.4 ~ 98.0
 8.0 ~ 10.0
 57.8 ~ 72.3
Wheel speed sensor mounting bolt
 6.9 ~ 10.8
 0.7 ~ 1.1
 5.1 ~ 8.0
Brake disc mounting screw
 4.9 ~ 5.9
 0.5 ~ 0.6
 3.6 ~ 4.3
Hub assembly mounting bolt
  78.4 ~ 98.0
 8.0 ~ 10.0
 57.8 ~ 72.3
Upper roll rod bracket bolt
 (A) 107.9 ~ 125.5
 11.0 ~ 13.0
 79.6 ~ 94.0
(B) 49.0 ~ 63.7
 5.0 ~ 6.5
 36.2 ~ 47.0
Lower arm ball joint mounting bolt
 98.1 ~ 117.7
 10.0 ~ 12.0
 72.3 ~ 86.8
Tie rod end ball joint mounting nut
  34.3 ~ 44.1
 3.5 ~ 4.5
  25.3 ~ 32.5
Rear
 Tire wheel lug nuts
 88.3 ~ 107.9
 9.0 ~ 11.0
 65.1 ~ 79.6
Driveshaft castle nut
 240.3 ~ 269.7
 24.5 ~ 27.5
 177.2 ~ 198.9
Shock absorber lower mounting nut
 137.2 ~ 156.9
14.0 ~ 16.0
 101.2 ~ 115.7
Brake caliper mounting bolt
 49.0 ~ 58.8
 5.0 ~ 6.0
 36.2 ~ 43.4
Wheel speed sensor mounting bolt
 6.9 ~ 10.8
 0.7 ~ 1.1
 5.1 ~ 8.0
Brake disc mounting screw
 4.9 ~ 5.9
 0.5 ~ 0.6
 3.6 ~ 4.3
Hub assembly mounting bolt
 78.5 ~ 88.3
 8.0 ~ 9.0
 57.9 ~ 65.1
Upper arm mounting bolt
 2WD : 137.2 ~ 156.9
 14.0 ~ 16.0
 101.2 ~ 115.7
4WD : 98.1 ~ 117.7
 10.0 ~ 12.0
  72.3 ~ 86.8
Lower arm mounting bolt
 137.2 ~ 156.9
 14.0 ~ 16.0
 101.2 ~ 115.7
Assist arm ball joint mounting nut
 137.2 ~ 156.9
 14.0 ~ 16.0
  101.2 ~ 115.7
Trailing arm mounting bolt
  34.3 ~ 53.9
 3.5 ~ 5.5
 25.3 ~ 39.7
propeller
shaft
 Front propeller shaft mounting bolt
 49.0 ~ 68.6
 5.0 ~ 7.0
 36.2 ~ 50.6
Propeller shaft center bearing bracket mounting bolt
 49.0 ~ 53.9
 5.0 ~ 7.0
 36.2 ~ 50.6
Rear Differential
 Rear propeller shaft mounting bolt
 49.0 ~ 68.6
 5.0 ~ 7.0
 36.2 ~ 50.6
Rear differential mounting bolt
 68.6 ~ 88.3
 7.0 ~ 9.0
 50.6 ~ 65.1
Differential cover mounting bolt
 39.2 ~ 49.0
 4.0 ~ 5.0
 28.9 ~ 36.2
Rear differential drain plug
 49.0 ~ 68.6
 5.0 ~ 7.0
 36.2 ~ 50.6
Rear differential filler plug
 39.2 ~ 58.8
 4.0 ~ 6.0
 28.9 ~ 43.3


Lubricants

Items
 Lubricants
 Quantity
Front driveshaft
 UBJ 104
 Theta 2.0 T-GDI / MT
 RBA
 165 ± 10g
Theta 2.4 GDI / MT, AT
 RBA
 150 ± 10g
LSJ 104
 Theta 2.0 T-GDI / MT
 SH06-VX21
 250 ± 15g
Theta 2.4 GDI / MT, AT
 SH06-VX21
 215 ± 15g
Rear driveshaft
 EBJ79
 NTG2218-M
 60 ± 10g
EDJ82
 NKG205
 80 ± 10g


General Information
...

Special Service Tools
Special Service Tools Tool(Number and Name) Illustration Use 09495-33000 Puller Removal of spider assembly from a drive shaft. 09568-4A000 Ball joint puller Remove the ball joint 09495-3K000 Band installer ...

See also:

Components and Components Location
Component Location 1. Head lamp (Low) 2. Head lamp (High) 3. Position lamp 4. Turn signal lamp 5. Side marker 6. Fog lamp 7. Turn signal lamp (Door mirror) 8. Overhead console lamp 9. Room lamp 10. Cargo ...

Repair procedures
Valve Clearance Inspection And Adjustment Inspect and adjust the valve clearance when the engine is cold (Engine coolant temperature : 20°C (68°F)) and cylinder head is installed on the cylinder block. ...

BJ Boot. Repair procedures
Removal 1. Remove the front driveshaft. 2. Remove the TJ joint assembly. 3. Remove the Dynamic damper. 4. Using a plier or flat-tipped (-) screwdriver, remove the BJ boot bands (A). 5. Remove the BJ boot. ...