Hyundai Santa Fe: Cruise Control Switch. Repair procedures - Cruise Control System - Engine Electrical SystemHyundai Santa Fe: Cruise Control Switch. Repair procedures

Removal

1.
Disconnect the negative (-) battery terminal.
2.
Remove the driver airbag module.
<a href="content.asp?vehicletype=Passenger&mfrcode=HY&area=HMA&langcode=ENG&modelid=AN13&modelyr=2013&mmctype=ab&mmcid=36&group=SHOP&pdftype=&cat1=2013+%3E+G+2%2E0+T%2DGDI&ec=&nLocation=1$2_1_3_1&firstnodedesc=Restraint&sitinfolist=81%5E8120%5E81200100%5Enone%5E801%5E1%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%2481%5E8120%5E81200100%5Enone%5E801%5E4%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%2481%5E8120%5E81200100%5Enone%5E801%5E8%5EENG%5EHY%5EAN13%5E2013%5Eab%5E36%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Restraint - "Driver Airbag (DAB) Module and Clock Spring")</a>
3.
Remove the steering wheel.
<a href="content.asp?vehicletype=Passenger&mfrcode=HY&area=HMA&langcode=ENG&modelid=AN13&modelyr=2013&mmctype=st&mmcid=4&group=SHOP&pdftype=&cat1=2013+%3E+G+2%2E0+T%2DGDI&ec=&nLocation=1$11_1_3_5&firstnodedesc=Steering+System&sitinfolist=61%5E6125%5E61250500%5Enone%5E801%5E1%5EENG%5EHY%5EAN13%5E2013%5Est%5E4%5Enone%5Enone%5Enone%5ESHOP%5E%2461%5E6125%5E61250500%5Enone%5E801%5E2%5EENG%5EHY%5EAN13%5E2013%5Est%5E4%5Enone%5Enone%5Enone%5ESHOP%5E%2461%5E6125%5E61250500%5Enone%5E801%5E4%5EENG%5EHY%5EAN13%5E2013%5Est%5E4%5Enone%5Enone%5Enone%5ESHOP%5E%24" target="_blank">(Refer to Steering System - "Steering Column and Shaft")</a>
4.
Remove the steering wheel cover (A) after loosening the screws.
5.
Loosen the screws after disconnecting the steering wheel remote control switch connector (A).
6.
Remove the remote control switchs (A).

Installation

1.
Install in the reverse order of removal.

Inspection

[Measuring Resistance]
1.
Disconnect the cruise control switch connector from the control switch.
2.
Measure resistance between terminals on the control switch when each function switch is ON (switch is depressed).
Function switch
 Terminal
 Resistance [kΩ ± 5%]
CANCEL
 2 - 7
 0.18
RES+
 2 - 7
 0.33
SET–
 2 - 7
 0.55
CRUISE
 2 - 7
 0.88

3.
If not within specification, replace switch.
[Measuring Voltage]
1.
Connect the cruise control switch connector to the control switch.
2.
Measure voltage between terminals on the harness side connector when each function switch is ON (switch is depressed).
Function switch
 Terminal
 Voltage (V)
CANCEL
 2 - 7
 0.76
RES+
 2 - 7
 1.41
SET–
 2 - 7
 2.05
CRUISE
 2 - 7
 2.66

3.
If not within specification, replace switch.

Cruise Control Switch. Schematic Diagrams
Circuit Diagram ...

Emission Control System
...

See also:

Hands Free Mic. Repair procedures
Inspection 1. Disconnect the negative (-) battery terminal. 2. Seperate the handsfree mic (A) from the roof trim. 3. Remove the handsfree mic (B) after disconnecting the handsfree mic connector (A). 4. ...

Smart key immobilizer system
Your vehicle is equipped with an electronic engine immobilizer system to reduce the risk of unauthorized vehicle use. Your immobilizer system is comprised of a small transponder in the smart key and electronic ...

Cargo security screen
Use the cargo security screen to hide items stored in the cargo area. ...