Hyundai Santa Fe: Oil Pan. Repair procedures - Lubrication System - Engine Mechanical SystemHyundai Santa Fe: Oil Pan. Repair procedures

Removal

1.
Remove the drive belt.
 
2.
Remove the A/C compressor.
3.
Remove the A/C compressor bracket (A).

4.
Drain the engine oil.
5.
Remove the oil pan (A). Insert the blade of SST (09215-3C000) between the ladder frame and oil pan. Cut off applied sealer and remove the lower oil pan.

•
Insert the SST between the oil pan and the ladder frame by tapping it with a plastic hammer in the direction of arrow.
•
After tapping the SST with a plastic hammer along the direction of edge of the oil pan, remove it from the ladder frame. arrow around more than 2/3 edge of the oil pan, remove it from the ladder frame.
•
Do not turn over the SST abruptly without tapping. It be result in damage of the SST.

Installation

1.
Install the oil pan.
(1)
Using a gasket scraper, remove all the old sealant material from the gasket surfaces.
(2)
Before assembling the oil pan, liquid sealant Loctite 5900H, Threebond 1217H or equivalent should be applied on oil pan. The part must be assembled within 5 minutes after sealant was applied.
Bead width : 3.0 mm (0.12 in.)

•
When applying sealant gasket, sealant must not be protruded into the inside of oil pan.
•
To prevent leakage of oil, apply sealant gasket on the inner threads of the bolt holes.
(3)
Install the oil pan (A). Uniformly tighten the bolts in several passes.
Tightening torque
Bolts B (M9) :
30.4 ~ 34.3 N.m (3.1 ~ 3.5 kgf.m, 22.4 ~ 25.3 lb-ft)
Bolts C (M6) :
9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

After assembly, wait at least 30 minutes before filling the engine with oil.
Always use a new drain plug gasket.
2.
Install the A/C compressor bracket (A).
Tightening torque :
19.6 ~ 23.5 N.m (2.0 ~ 2.4 kgf.m, 14.5 ~ 17.4 lb-ft)

3.
Install the A/C compressor lower bolts.
4.
Refill engine with engine oil.

Oil Cooler. Repair procedures
Removal 1. Loosen the drain plug, and drain the coolant. Remove the radiator cap to help drain the coolant faster. 2. Disconnect the oil cooler coolant hoses (A). 3. Remove the oil filter (A). 4. Loosen ...

Balance Shaft & Oil Pump. Components and Components Location
Components 1. Balance shaft & oil pump assembly 2. Balance shaft chain tensioner 3. Balance shaft chain 4. Balance shaft chain sprocket 5. Balance shaft chain guide 6. Balance shaft chain tensioner ...

See also:

Rear parking assist system precautions
The rear parking assist system may not sound sequentially depending on the speed and shapes of the objects detected. The rear parking assist system may malfunction if the vehicle bumper height or sensor ...

Front Seat Back Cover. Repair procedures
Replacement • Put on gloves to protect your hands. • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage. • ...

Valve Body. Repair procedures
Removal 1. Remove the air duct. 2. Remove the battery and the battery tray. 3. Remove the under cover(A). Tightening torque : 7.8 ~ 11.8 N.m (0.8 ~ 1.2 kgf.m, 5.8 ~ 8.7 lb-ft) 4. Drain the coolant. 5. ...